|09-12-2012 09:03 PM|
|jerseYJ||and never use tow straps, only recovery straps, with a wet t shirt or towel placed over tensioned strap. and no should be standing in the open and watching.|
|09-12-2012 04:12 PM|
And yeah, the factory bumper is a thin sheet of metal, don't expect it to hold.
But truth be told, no matter what you are using, if it's stuck that bad, NO ONE should be standing anywhere around the vehicle in the open when the pulling begins.
|09-12-2012 02:57 PM|
But my main point is to never wrap a tow/snatch strap around or attach anything to the bumper itself which is little more than thin sheet metal. The bumper is defintely not a structural part of the frame.
|09-12-2012 02:41 PM|
Just throwing this out there to remind everyone to be carefull. I know for a fact that one vehicle was pulling out another vehicle with a nylon strap placed over a very similar hook. The hook pulled out of the vehicle frame where it was mounted and the strap propelled it 100' through the air and through the rib cage of a man standing by killing him instantly.
The hook didn't break but what is believed to have happened is that one bolt broke and then the second bolt pulled through.
Unless a vehicle is only slightly stuck I would use a strap wrapped around something substantial like the whole bumper or part of the frame and not rely on two little bolts to hold.
If its not too bad you would be fine but if its burried I wouldn't use those hooks.
I'm not an engineer but it might help to use some kind of back plate on the other side if possible rather than just the nuts and washers.
|09-12-2012 02:35 PM|
|Neil F.||If they come with 1/2 bolts, they should fit but you need at least grade 5 or best grade 8 bolts. You can search on the internet for the markings. The top of the heads will have hatch marks indicating 5 or 8|
|09-12-2012 01:55 PM|
HF still has these on sale until the end of September for $5.99 each.
Also, did you leave the little clip on or mount without them?
|08-31-2012 10:55 PM|
|08-31-2012 10:06 PM|
|DevilDogDoc||8.8 is metric grade 5 I believe.|
|08-31-2012 06:07 PM|
|07-18-2012 07:54 AM|
|Tonycrd||If you want OEM position you will have to take the bumper off. There is a round chasis crossmember behind it that makes it impossible to reach the studs.|
|07-18-2012 07:43 AM|
|07-17-2012 08:49 PM|
Thanks for all the info...and the measurements. Hope I can install the bumper guards tonight, going to paint them first so may let them dry overnight before installing them.
Question: do I have to take the front bumper off to be able install the bumper guards?
|07-17-2012 12:58 PM|
But yeah, the ones at HF do come with hardware, they even have like a clip on them.
And yeah, they line right up with the factory bolts in the bumper/frame. I put mine on sitting right in front of the hardware store where I bought the bolts.
And if you have a hitch in the back.... also at Harbor Freight for $10.
|07-17-2012 12:50 PM|
[QUOTE=Dragonii;2593404]Tow hooks... Summit and Harbor Freight both sell them for $10 per hook. Grade 8 bolts, cheap at the local Ace Hardware. Cheap, strong, quick and easy to install. They do the job, got me out of a big mud hole just two days ago.
My niece says that they look like claws or fangs. lol
Those look good; Harbor Freight lists them for $7.99 including hardware and safety clip with a 10,000 lb rating. Might have to go get me some. I'm guessing the holes line up?
|07-17-2012 12:39 PM|
Tow hooks... Summit and Harbor Freight both sell them for $10 per hook. Grade 8 bolts, cheap at the local Ace Hardware. Cheap, strong, quick and easy to install. They do the job, got me out of a big mud hole just two days ago.
My niece says that they look like claws or fangs. lol
|07-17-2012 08:49 AM|
|Tonycrd||Hiya! Good to see you still have a Jeep!|
|07-17-2012 06:56 AM|
I have a 2001 and not sure if PO relocated bumper pads or not but from the center of the outer bolt to end of metal bumper on mine it measures 4.5 inches. PO had installed towbar attach points to front bumper and welded through frame so maybe my pads are more outboard than normal.
Tonycrd, good to hear from you. been a long time, used to bump into you frequently on LOST as Liberty2.8 when I had my CRD, I sure miss it.
|07-17-2012 05:50 AM|
Couldn't find a better pic but this is what jlpete98 means, the OEM towhooks are in the centre of the rubber guards.
|07-17-2012 05:25 AM|
|jlpete98||From outside edge of the metal bumper to closest edge of rubber is 10 1/4 inches. The center of the rubber piece is about where the tow hook-not bolts, but hook, is located|
|07-17-2012 05:12 AM|
Thanks for the ideas but like Jerry said, it wouldn't be safe...plus I've already bought a pair of the stock bumper pads for only $15.
If anyone could pull a tape measure to those holes and snap a picture of it today that would make my day...I'd like to install them tonight while at work. Thanks again guys.
|07-17-2012 12:17 AM|
|05silver_sport||Whoops don't listen to me then thanks for saving my a$$ Jerry boy. :O|
|07-17-2012 12:10 AM|
Do NOT weld D-rings onto those thin sheet metal factory bumpers!
The factory sheetmetal bumpers aren't strong enough and you cannot simply weld D-rings onto the surface of even strong heavy-duty bumpers... they must be through-welded by a tab passing entirely through the bumper that is welded on both sides. Welded onto the factory bumpers, the D-rings would be ripped right off with a decent pull and likely harm/injure/kill someone as the strap or cable and shackle flew back away from the bumper after it tore free of its weld on the thin sheet metal.
The only safe way to add shackles onto a stock bumper is to use the type that bolt onto the top of the bumper (like tow hooks do) via Grade 5 or Grade 8 bolts that pass through the bumper into the frame below.
|07-17-2012 12:06 AM|
|05silver_sport||I understand wanting the stock look but for less than the price if two of those why not just some buy D ring mounts and D-rings and weld then onto the bumper that's what I'm planning on doing to mine I feel it's a more rugged look and you add two more tow points to your front end. Just a suggestion.|
|07-16-2012 10:13 PM|
Stock front bumper question.
My Jeep is a 97 Sahara. I'm wanting to add the front bumper guards to the stock front bumper but the 97's didn't come with them. I picked up a pair really cheap but my bumper doesn't have the holes pre-drilled. Was wondering if someone that has a stock front 98+ bumper could post some measurements up for me. If you could measure from the outside edge of the metal bumper to the outside holes where the bumper pads attach...I should be able to use the bumper guards to figure the inner holes. Even could just pull a tape measure from the bumper edge to the holes and snap a pic of it and post it that would work too. Anyone's help will be greatly appreciated. Thanks in advance!
This is the bumper guards I'm wanting to attach, but used: