Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Flat tow

Join Wrangler Forum Today


Thread: Flat tow Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-25-2012 03:13 PM
robtbritn
Quote:
Originally Posted by 20ga View Post
Tow bar and wiring is less than $200.

The base plate adds to the cost.

Do not tow off the stock bumper.
$120 for this set up...eliminates having to buy a base plate, mounts directly to the front frame rails (under the bumper). Just need to add the tow bar and wiring. With that said, check your states requirements for supplementary brake device for towed vehicle and brake away system...now your getting into more $$. I use M&G Engineering with my bus equipped with air brakes.
Currie Enterprises CJ Axle Parts
M & G Engineering - Car Braking Systems: Home Page
07-25-2012 01:17 PM
20ga Tow bar and wiring is less than $200.

The base plate adds to the cost.

Do not tow off the stock bumper.
07-25-2012 11:40 AM
Dextreme
Quote:
Originally Posted by DLH View Post
Ok, thank you! We have found that it is rather expensive to get set up!
I have about $150 total into my set up for the towbar and wiring/lighting.
07-25-2012 10:28 AM
robtbritn I've been using this set up for years towing my 2004 TJ behind my Motorhome. It mounts to the bottom of the TJ frame under the bumper...clean and simple.
Currie Enterprises CJ Axle Parts
07-25-2012 10:08 AM
20ga www.hitchsource.com

I just installed the Blue Ox base plate and also bought their width adjustable tow bar. The entire setup was about $600+. Good stuff.

As for wiring just get three diodes and splice them in at the wiring running along the drivers side rocker panels inside the cab. Run the wiring to the tow vehicle through the firewall close by. No need to drill a hoe just pook through and existing spot with other wires. You can get the diodes from hitchsource. They are very easy to install. It is not necessary to add light bulbs to your tail lights!!

Wrangler left turn/stop dark green/red to yellow from tow vehicle.
Wrangler running white/yellow to brown from tow vehicle.
Wrangler right/stop brown/red to green from tow vehicle
Ground the white wire from the tow vehicle on the bolt that holds the door strap to the body.
07-24-2012 09:20 PM
DLH Ok, thank you! We have found that it is rather expensive to get set up!
07-24-2012 04:59 PM
Dextreme I just flat tow a few times a year and this is what I use:

Tow Bar - Adjustable Tow Bar w/ 5000 Lb. Capacity

and here is my Flat Tow thread: http://www.wranglerforum.com/f5/sett...ow-136535.html
07-24-2012 04:51 PM
DLH
Flat tow

Need recommendations for tow bar and base plates for 2005 Rubicon.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:45 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC