|04-22-2013 05:56 PM|
|caposto||I had the opposite problem: U-joint was too tight. I have an SYE and new driveshaft and the tolerences appear to be a little tighter on my driveshaft for the rear u-joint. I ate through the original u-joint pretty quickly. When I replaced it I really compressed it and still couldn't get the c-clips in. The straps fit perfectly on the diff side. I ended up grinding down the thickness of the c-clips just a tiny bit and it fit into the driveshaft just right.|
|04-22-2013 09:08 AM|
|04-22-2013 01:02 AM|
Been having the same problem. Couldn't make a U joint last a week for about a month. My rear end was bad so I replaced that and it helped. But here I am today with another U joint torn to pieces.
My questions is my rear leaf springs are warn out. Just haven't had the money to replace them. But does this cause a slow deterioration of the U joints over time?
|08-05-2012 10:38 PM|
|08-02-2012 02:57 PM|
|Benjamb||OK, my 90 YJ (4.2/5 speed) ate two rear U-joints in the last 15 miles. I am wondering if I may have lost the first one due to lose strap bolts and perhaps the second due to damage (bent?) driveshaft from the first failure. I will order new u-joint components and confirm the size but I wonder if I should replace the drive shaft. Is there a rear bearing in the transfer case I could have damaged? Thanks.|
|08-02-2012 02:22 PM|
What year jeep do you have and what part number was the correct one? I need a new u joint in Mine. How do you install the new one? Figured you could help
Seeing Youve done This multiple times.
|08-01-2012 07:44 PM|
|rich jazz||Well they were the wrong size, correct box, wrong product inside. Had wrong size for 3 years, what a different jeep it is now.|
|07-29-2012 06:45 PM|
|rich jazz||Thanks, that would explain why I keep eating ujoints, will order new ones from quadratec.|
|07-29-2012 05:35 PM|
The spicer part numbers are 1310(stock for the older YJ's) for the smaller and 1330(stock for the newer YJ's) for the bigger joint. I'm not sure which ones you would need, cause mine is a CV joint shaft that doesnt take either.
|07-29-2012 02:31 PM|
|rich jazz||I think I have same problem. just changed ujoints about 3 months ago and are making noise again. when I tighten straps up, i can still move shaft back and forth a little. would that be the wrong part?|
|04-15-2012 01:06 PM|
|AZ WRANGLER||Make sure the end of the u-joint is touching the little bump stop inside the yolk. There should be little square stop that holds the end of the ujoints in place. If you have the wrong size, it will be short of this little stop by about 1/8". I will get you pics today if I can.|
|04-15-2012 12:56 PM|
|90islander||Its got a 4" lift but the ds is at a good angle its got a drop kit on it, i cant remember what brand joints i got but ill male sure and get the right joint also|
|04-15-2012 12:21 PM|
The rear is a different size than all the rest. It is bigger. Make sure you are getting the correct one to fit.
The retards at the parts store will tell you they are the same, but they are not. The fronts will fit, but be about 1/8 shorter. This allows movement and desroys the u-joint.
|04-15-2012 09:08 AM|
|HHSOCCER28||Are the sections of the driveshaft all in phase?|
|04-15-2012 08:40 AM|
|year1camaro||Sounds like your pinion angle could be off.....worn out springs could be the cause.....a lifted jeep could also do it. Or you could just be an animal behind the wheel. lol ....Did you grease the u joints when you changed in the new one before you drove it?|
|04-15-2012 08:01 AM|
|95YamJam||Are you using cheap joints? Is your jeep lifted? Driveshaft out of balance?|
|04-15-2012 03:47 AM|
rear ujoint help
i have owned my jeep for 9 months now and i am getting ready to put the 4th ujoint in the rear ds, i have no idea y i keep eating ujoints up