Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Electrical Gurus please step inside

Join Wrangler Forum Today

Thread: Electrical Gurus please step inside Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-09-2012 02:40 PM
Flashole Awesome! Thanks for the help!
08-09-2012 07:57 AM
RJPII I would probably choose the heater lights since they are easier to find, just look for the bulb (radio light is probably off an internal relay). You can daisy chain the switches (power, ground, lights).

Getting the terminals out of the socket is not usually an easy task. As you can imagine they are designed to stay put. I would check the amp rating for the socket, make sure it matches with the relay. You can figure out how many amps you are pulling using this formula Amps = watts/volts. You can determine the right size wire to use bases on this also. Just follow the AWG gauge below to determine the wire size needed. Too large of a wire can be bad too, so you want to be around the right size.

AWG Amps
10 13.88
11 10.98
12 8.71
13 6.9
14 5.48
15 4.34
16 3.44
17 2.73
08-08-2012 08:03 PM
Flashole Thanks for the help! I think I have a pretty good understanding now of what goes where. I do have a couple more questions though.

Any suggestions on the best place to pull dash light power from? The radio and heater control lights are the closest things that light up when the lights are on. Would this be a good place, or is there a more ideal place?

I'm installing 4 switches in a row. I understand that I will need to run individual wires from each switch to control each realy, but is there any reason I can't just daisy chain all the switches together for the switch power, the dash light power and the ground wire?

Any clue how to get the terminals out of the relay sockets? If at all possible, I'd like to use a beefier wire for the main power from the battery.

ETA....its a 2001 TJ
08-08-2012 08:40 AM
RJPII Just one more note. Make sure you secure the relay so the posts face down. This will prevent water getting caught in the relay and shorting anything out.
08-08-2012 08:37 AM
RJPII By no means an electronic guru, but let me see if I can help.

Where to tie in #8 would really be jeep specific, but I would think that tying into a powered light in the center console (lights for heat) would be the easiest.

#3 does go to #85 on the relay.

#2 is the main power supply for the switch (not the accessory). Any power supply should work fine, but a direct fuse box would be best. The main power supply should come off the battery and tie into #30 on the relay. This should be a fused line.

87A is only on a SPDT relay (single pole/dual throw) and in your case does not have a use. If you're not using a wiring harness for the relay, you should cover it with something, because it will be energized when the switch is off. You do not want it to ground out. The other option would be to pick up a SPST (single pole/single throw) relay.

Check out this website. It does a pretty good job of showing how a relay works.

Hope this helps, good luck with the project!
08-07-2012 11:20 PM
Electrical Gurus please step inside

I bought some lights and ordered some switches, relays, wire, in-line fuses, etc, but I'm a little confused about how to actually hook it all up.

From the schematic, it looks like I would jump 6&7 and run it to ground. Simple enough.

#8 obviously ties into a dash light power wire somewhere. Any clue where the best place to tie into one of these is?

I'm assuming that the #3 lead on the switch gets connected to the #85 lead on the relay. Is that correct?

But, I'm a little confused what to hook #2 up to? Does it just need a power supply? If so, where is the best place to pull power from? Would the cigarette lighter work? Or, would somewhere off the fuse box be better, or does it just go straight to the battery?

Also, on the relay schematic, it doesn't appear that 87a is hooked up to anything........What would this slot be reserved for?

Switch schematic.

Generic Relay schematic I found on-line

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 03:25 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC