Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > WOOO ITS RUNNING... wait... wtf is that noise... oh shi, shut it down, SHUT IT DOWN!

Join Wrangler Forum Today


Thread: WOOO ITS RUNNING... wait... wtf is that noise... oh shi, shut it down, SHUT IT DOWN! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-11-2012 09:24 AM
DILLIGAF So another way to check for spark you could just pull a plug and wire off and lay it across something to ground it and have someone turn the key, while you are watching the electrode. This will tell ya for sure,
08-11-2012 06:23 AM
medicjz The ICM can cause a no fire situation. When mine was going bad, it would sometimes run well, sometimes run like crap, and then sometimes not allow firing at all. When mine would not fire at all, it was always after a period of it running well, and I believe getting warm. I tested it with the hammer method...if it won't start...hit it with a BFH and try to turn it over. It worked and that is how I figured it was bad.
08-09-2012 10:56 PM
89YJ Convert this is a WALL of text. just be warned.

I replaced the water pump today. It ran awesome... for all of a mile. it was the waterpump that was causing the weird noise... whats causing this, idk.

what happened was this. I was bleeding air out of the system after refilling the radiator so I was running it around the neighborhood, coming back, topping off again, running around, rinse repeat three times. ok, so I come back after all that and it's running insanely awesome. I figure I'm done working on it for awhile so I rinse off the grease I had gotten all over it while working on it. I was VERY careful not to get any in the engine bay, it might have gotten a few drops here and there; not enough, I would think, for a jeep to have a fit about it. I take it around the block once more as a sort of celebratory lap for fixing it... get back and 5 feet before I'm in my parking spot it starts running funny, like its not firing right/at all on half the cylinders. then it cuts out. I tried to restart it and it catches a few times, stalls out and then lets out a HUGE backfire.

I hooked a timing light to it and I'm not getting anything. now this timing light has been patched together after the fan ate it and I wasn't able to check the timing light on anything else as my jeep is the only car at the house that actually has plug wires. It is a possibility in my mind that my timing light isnt working... though it was working before. if, however, it is working then I'm going to rule out the ignition module as my understanding is that if that is going bad it'll more mess up the firing rather than not fire at all. that leaves the coil and the distributor. I already took the distributor apart... its pretty much new... so the coil... idk, I guess I'll check that tomorrow. aside from that, there's only wiring... which a lot of has been replaced for the ignition system because it fried itself about a month back... damn Im tired of doing all this work for this thing to run for all of a couple miles before it breaks again...
08-09-2012 10:13 PM
Nubby55 if the dizzy was 1 or 2 or 8 teeth off the timeing whould be the same advance just the dizzy whould be turned cock eyed are have to move the wires to match, the timing liight would look the same on the crank. drop the belts as said before and run it and go from there.
08-08-2012 07:29 PM
CharTay U didn't tighten the pullys to tight did u?
08-08-2012 07:12 PM
ballistx
water pump let loose

The water pump absolutely should not have anything "loose'. However, if something inside the water pump lets loose it really shouldn't hurt anything except the water pump itself. If a part of an impeller lets loose it will be pushed into the engine cavity until it lodges. If it lodges in a manner that blocks a port then there could be an internal hot spot. But not likely. Mostly the impeller will slip on the shaft. If it got too loose it could wobble and cause the sound you are expressing.

Best to pull the water pump and see what you find. If nothing, then it sounds like at least popping the timing chain cover to see what's what inside.
08-08-2012 04:58 PM
0III0forlife First thing i would do is take the belts off the water pump and then start it back up.

If you get no noise, then you know where the problem is.

As fas as the 15 degrees advanced, that is quite high, sounds almost like the dizzy is a tooth or two off.
08-08-2012 03:56 PM
89YJ Convert
WOOO ITS RUNNING... wait... wtf is that noise... oh shi, shut it down, SHUT IT DOWN!

right so, I got the 89 wrangler with the amc 258 running just so again today. I mean I was hootin and holloering cause it was pulling strong, running like a champ after a timing chain replacement, then, all of a sudden I get a loose metal noise. you know that noise that instantly makes your eyes get about two times as wide and your stomach drops cause you know something broke? yeah, that noise. metal on metal clunking. a light clunking not a heavy knock or anything but that noise that tells you that something, somewhere that shouldn't be loose, is loose, somewhere it shouldn't be. well, I got back home ok kind of babying it. pop the hood and try to listen for the noise, it wasn't presenting so i revved it a little, and I get that metal flying around almost a grinding this time sound from the front of the engine.

Now, my water pump has quite a bit of play in it. I'm going to be replacing it tomorrow when I get paid. what I want to know before I take this thing apart is this, if the water pump had a serious failure, could something have broken off and caused any serious damage? also, any possibility that something isnt right with the timing chain I just replaced? I did it all by the book, everything got tightened down damn tight. I can't think of anything that would be causing this noise from that department. I am running an awful lot of timing advance (about 15 degrees) for having installed the chain to the T though. 15 links between marks with camshaft sprocket at 1 o clock and everything. I'm scratching my head here. any advice would be helpful. any questions, just ask.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:22 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC