Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Gas tank skid plate removal.

Join Wrangler Forum Today


Thread: Gas tank skid plate removal. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-10-2012 04:19 PM
markharmon I can tell you from experience the nuts holding the plate to frame is some kind of crush type nut. it gets wedged in at factory went they tighten bolt. So later in life it just spins when you crank on it. I ended up welding some nuts on 1/8" steel and sliding it inside frame. Of course I was replacing that section of frame. So I had it completely cut out of jeep. Passenger side drilled small holes and pumped it with no blaster first.
08-10-2012 04:13 PM
markharmon Hardest part I had was the front bolts. Something about cutting wheels sparks and gas in the same area.
08-10-2012 02:54 PM
90DesertTanYJ Also helps to have a piece of 2X4 to spread the weight on the top of the jack. Mine had 7 or 8 gals of 3 year old fuel in it and it was a pain. Like said above the less fuel the better.

Take the filler and vent hose loose, take off the 4 back bolts, drop down enough to do what you need or if complete removal is necessary, you ave 3 hoses up top and then 3 bolts up front. lower tank and skid out of the way.
08-10-2012 01:39 PM
raycer removing the tank isn't hard at all. The biggest annoyasnce is the exhaust tend to get in the way. Much easier is you remove the tailpipe, or just have someone pull on it to get it out of the way. I did it by myself but it was a pain; wuldv'e been faster if someone was their to hold the pipe away.
08-10-2012 01:34 PM
redmanwalking That does help. Too bad its not going to be as easy as I thought.
08-10-2012 10:13 AM
Brad87YJ I replaced the gas tank on my 87 YJ many years back. Sand and grit will get between the gas tank and skid plate and eventually rub a hole into the gas tank.

Anyway, the best I can remember is that the skid plate does hold the gas tank in place. It is very easy to remove the skidplate and gas tank and can be done with one person and a floor jack. The less gas in the tank the better when you go to do it.

If you don't need to take the tank completely out, you shouldn't really need to disconnect anything except maybe the filler hoses and vent, which I think are just hose clamps. Then you can remove the front and back bolts and lower the tank using the floor jack. Keep an eye on the fuel lines and the wires going to the top of the tank and you might be able to lower the tank just enough to gain access to what you need to without having to disconnect anything else.

Hope this helps.
08-10-2012 10:04 AM
zoomwide The skid plate is supporting the gas tank. I had to drop mine this week to fix a leak on top of the tank.

The only not-so-obvious factor is the straps. On the rear of the tank, there are two nuts/bolts which are the ends of the straps. Those do not have to be removed. Excluding those, there are three on the front and three or four on the back. Make sure you disconnect your battery and have a floor jack ready to take the weight of the tank as you loosen.

there a couple of good threads out there with more detail
08-10-2012 09:53 AM
redmanwalking
Gas tank skid plate removal.

I need some guidance on removing the skid plate over the gas tank. Is this supporting the tank? How many and where are all of the bolts for the plate located.

I'm trying to install a bumper and I cannot get to 4 of the bolt location because the skid plate is in the way.

Help me out before I start smashing things!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:22 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC