Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Having electrical issues

Join Wrangler Forum Today


Thread: Having electrical issues Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-01-2008 04:17 PM
jpdocdave let us know, and just a really quick little info on why it is most likely a ground. a bad or weak ground allows the voltage to backfeed through that ground, putting weak voltage to other bulbs and junk like that.
10-01-2008 12:18 PM
Brad W You guys are the best. I will pick up a manual and check out the diagrams. Wish me luck. I appreciate all the input.
10-01-2008 09:56 AM
whiteyj Brad, I second jpdocDave's comments. Get the manual and spend some time with it to correct the problem. You'll be far better off in the long run learning the in's and out's of a 14 yr old or more vehicle. Otherwise you could find yourself SOL in the back country with a dead battery and no help around.
10-01-2008 09:49 AM
endzone80 To me it sounds like the wiring. If your car has been exposed to a lot of heat, or ran real hot on a few occasions for whatever reason, the coating on the wires sometimes will melt and fuse with another wire. This can potentially cause cross voltage - sending the wrong amount of voltage to the wrong place - thus creating a surge of power on one thing, and a deficit of power on another.

You can also just try tipping the guy doing your inspection a little bit of money, and have him pass you. Never fails for me when I need it.
10-01-2008 07:20 AM
jpdocdave i'd say get yourself a haynes or some kind of repair manual with wiring diagrams. probably all your problems are from one bad wire or ground. good luck
09-30-2008 06:04 PM
Brad W I am far from mechanically inclined. Where would I check the grounds and find the sockets?

The passenger side blinkers are both the one on the front wheel well and also the back tail light. Do you think that could still be a bad bulb?

I really do appreciate your help.
09-30-2008 05:52 PM
jpdocdave sounds like a bad ground, check, clean and tighten grounds. check for corroded nasty sockets also. check for a bad bulb with the blinker on one side going erratic. good luck, sometimes its real easy, sometimes its not
09-30-2008 05:29 PM
Brad W
Having electrical issues

I am desperate here. 1993 Wrangler will not pass inspection because of an electrical issue. The passenger side blinkers blink erratically when I turn on the turn signal. Also, when I press the brakes, the dashboard lights light up and the yellow lights below my head lights light up. Any suggestions on what I can do to correct this? Any help would be greatly appreciated bc I am broke and can't afford a mechanic. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:45 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC