Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Skid plate selection

Join Wrangler Forum Today

Thread: Skid plate selection Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-30-2012 08:44 AM
geiman The skid row should have a hole for the oil to drain through unless they've changed something, so it should still be easy to get a wrench on the oil pan drain bolt. The valve linked above is nice, but not a necessity. Not sure it would work with some of the plates that hug the pan like mine.

The only time you should need to remove the plate should be when doing something like dropping the transmission pan. Never worked with a Skid Row plate so I'm not sure how time consuming it is, but I doubt it takes much.
08-29-2012 09:58 PM
BLK00TJ Fumoto Engine Oil Drain Valve Installation - Jeep
08-29-2012 09:55 PM
Originally Posted by mdutton View Post
I ordered the Skid Row skid plate. It appears to be straight forward but effective. Hopefully it will still be easy to take off for servicing. It is suppose to arrive tomorrow
You can get a valve for the oil plug to make oil changes easier. Hook up a tube and turn the valve. I'll see if I can dig up the link. I was just looking at it the other day.
08-29-2012 09:52 PM
mdutton I ordered the Skid Row skid plate. It appears to be straight forward but effective. Hopefully it will still be easy to take off for servicing. It is suppose to arrive tomorrow
08-27-2012 09:35 PM
IslandTJ I run Skid Row, I use it and I like it. It mated well when I ran the stock OEM transfer case skid and likewise when I later upgraded to an UCF transfer case skid.
08-27-2012 07:22 PM
Water Dog Just put a good sized dent in my oil pan doing the Rubicon without protection for the pan. I'm going to take it off, pound it out, then do what a lot of others up there have done....Weld a piece of 3/16 or 1/4" plate right to the bottom of the pan....Heck, some of the after market plates bolt to the pan bolts and the bell housing anyway. This way it keeps it as high as possible and still offers protection.
08-21-2012 11:42 AM
Originally Posted by mdutton View Post
Anyone else got any suggestions?
read this:
So you want a Tummy Tuck... -

yes, it's got tummy tuck in the title. read it anyway for the info.

fwiw, you don't NEED to do a BL....
08-21-2012 10:45 AM
mdutton Anyone else got any suggestions?
08-21-2012 10:42 AM
mdutton I am not planning a tummy tuck. Dothe not really want to do a body lift. Just looking for something fairly simple
08-20-2012 11:24 PM
TnDz TJ There is a lot to think about when you talk about skids for the oil pan, tranny and t-case....

Are you thinking of a tummy tuck at the same time? I ask because a lot of components and LOTS of money and time get consumed in the process. There are several threads covering such topics that will shed some light on the costs involved.

I just did the UCF TT WITHOUT the oil pan and trans skid...I plan on adding it later

.. base components are as follows for just the TT:

-High Clearance skid ( of course)
-Minimum of 1" BL for tub clearance and/or a Lopro mount can be used
-1" MML ( Motor Mount Lift)
-Adjustable Rear Upper and Lower Control Arms ( I recommend both )
-SYE ( recommended a megshort SYE to lessen the driveline angle )
-Rear CV style Drive-shaft ( required with SYE )
-Rear shock re-locators
-Adjustable rear track bar and/or angled track bar bracket to allow pinion rotation
- possibly' a Novak shift cable for t-case... you may be able to modify existing linkage to work, I did...
-There may be some mods involved with exahaust..
- 6 new 1/2x13 skid plate bolts since the OEM bolts are 'bowled' and won't hold the skid properly

All in all... you are looking at about $1200-$1500 for a complete install if you are starting from scratch.
08-20-2012 09:41 PM
BLK00TJ Check out Under Cover Fab
08-20-2012 09:36 PM
Skid plate selection

Looking for some recommendations as to what the best skid plate is to protect the tranny oil pan and possibly the engine oil pan for a 2005 TJ with 4.0/Auto. It does not have any lift kit at this time. Attended a Jeep Mania event this weeken and bend the stock skid plate up pretty bad on one of the rock gardens on the obstacle course. It slight dent the tranny oil pan. Luckily it was not bad it could have been must worse.There must be something better out there. Nice to have something that can be removed without too much work so it will still be easy for service work. But not comprise protection. Looked at a Skid Row one on Quadratec Any thoughts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 11:29 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC