|08-22-2012 07:24 PM|
|Water Dog||Before you dismiss clutch problems, Also check the bushing that the clutch pedal swings on for play. I agree with SPEC-01 that 1st and reverse gears are the toughest to get into and the fact that you can get it into 1st while still moving, makes me lean toward a clutch issue. It sounds to me like the clutch is not completely disengaging. Another thing to consider is, was it shifting okay right before your throwout bearing blew up? If it was, the only thing that has really changed is the clutch work. JMHO|
|08-22-2012 02:34 PM|
As a point of reference that may help others with similar issues in the future: The clutch performs the same job no matter what gear you are selecting. This means that if clutch release is to blame it would affect other gears too most notably reverse. 1st and Reverse gear are often the hardest to slect because they are chosen from a stopped position where you have no mechanical advantage to aid in getting the car in gear.
Because you are seeing an issue with the selection of one gear only it is highly unlikely that this is clutch related. I suggest that you have the transmission torn down and examined for synchro, fork, pads, blocker-rings, etc... I also suggest addressing any other wear related issues while it's apart so you don't have to do this job again for similar issues on other gears.
I know this might not be what you wanted to hear...but, it's better to address the actual issue than to waste money "fixing" things that aren't broken! Let me know if you have any further questions and I will be happy to assist further! Thanks,
|08-22-2012 04:06 AM|
|Rommelx3||it's gotten to the point now where if I'm at a stop light and I don't shift into 1st before I come to a dead stop then it won't go in at all unless I really I mean really force it into gear.|
|08-22-2012 04:05 AM|
|08-22-2012 04:02 AM|
Good to know, I wasn't entirely sure if it could have been due to a resurfaced flywheel but since yours was resurfaced and didn't cause issues that eliminates the flywheel possibility.
|08-22-2012 04:01 AM|
|08-21-2012 02:01 PM|
|Moody715||I rebuilt my engine and put in a new clutch and I resurfaced my flywheel and never had any issues with mine shifting. Idk if this helps but I can say I have done it with no problems. Going on 35,000 miles after the rebuild.|
|08-21-2012 01:30 PM|
|08-21-2012 09:05 AM|
|dbxtr3||The syncro's in your transmission are wore out. You need a rebuild on the tranny. My jeep does the same thing @ 233,755 miles.|
|08-21-2012 03:10 AM|
|Rommelx3||trans mounts are new, anyone know symptoms of a tranny going bad?|
|08-21-2012 01:11 AM|
|ken78744||Well then I would think it is the transmission mount being busted then maybe, if not maybe then it is the transmission, take it by another shop get another opinion....|
|08-20-2012 03:02 PM|
The clutch pedal never felt hard to push in at all.
|08-19-2012 05:08 PM|
|ken78744||Find a Jeep only shop in your area call them ask them if they would or wouldn't resurface the flywheel on a clutch job, I bet not unless it was warrented....|
|08-19-2012 05:06 PM|
|08-19-2012 04:58 PM|
|Full Spool||My money says "rebuild the tranny".|
|08-19-2012 04:54 PM|
transmission or clutch?
hello TJ community,
I could really hear some advice/opinions/theories as to what is wrong with my jeep.
June of 2011 I purchased my first jeep: a 1997 standard transmission 4.0 wrangler with the ax-15 transmission. It had 150,000 miles on it when I bought it. It was a clean jeep, no rust, clean interior, hard top and full doors.
I had no problems with it until six months in the throw out bearing in the clutch system went bad (disintegrated) I had a 4x4 shop put in an LUK clutch. I read on this forum somewhere that when doing a clutch job on TJís the flywheel shouldnít be resurfaced due to itís unusual slight dome shape. I asked the shop about not resurfacing the flywheel and they insisted on resurfacing because they said theyíve done plenty of clutch jobs on jeeps and they said they always resurface the flywheel.
So the shop put everything in and resurfaced the flywheel. The jeep drove like new for a good 3 months until it started becoming increasingly difficult to put the jeep into first gear, I started having to shift it into another gear first and then it would shift into first.
Shifting when the jeep was cold was easy but once driving around in hot weather it became increasing difficult to shift. The floor also got really really hot. Iíve had the carpet out since Iíve owned it and the floor usually became warm but never really really hot.
I figured the shifting issues were due to a bad master or slave cylinder since the clutch was brand new and I donít ride the clutch. I ordered a pre-bled slave/master cylinder unit from amazon (oem) and put it into place (it was surprisingly simple to install) The new slave and master cylinder didnít help at so I took it back to the shop that installed the clutch to see if there was anything wrong with the clutch (I was still under warranty)
so to my surprise the shop said that my transmission was going bad! They said it needed to be rebuilt.
I took my jeep to a transmission repair shop in another area and they said that my transmission is fine and that the shifting issues are from the clutch not disengaging properly.
So Iím not really sure what the problem is, Iím thinking I might take it to a third place to get a third opinion. Could this be an issue caused by a resurfaced flywheel?