|10-12-2008 01:20 PM|
|Never Monday||but the stuff necessaryt o run 35's properly adds up quick|
|10-12-2008 12:54 PM|
In that case I'd go with 3" suspension lift and another in bl and add some 33s
Look at the tire prices though the jump from 33s to 35s is not that much
|10-12-2008 12:31 PM|
Well my "plan" for now is to do some lighting mods,get rid of the damn tape deck and tuna can speakers, and im thinking of just a 2" spacer lift.
Its a toy but i still have to run the 3 little kids around. My brother is pushing for a 4" lift but i cant afford big rubber... i have a firarm addiction i still have to throw a bone once and awhile...lol
|10-12-2008 12:26 PM|
Snowbanks will be fine btw
|10-12-2008 11:55 AM|
Now i dont "plan" on doing any major wheelin with this jeep but will the "turd axel club" be able to work trails,snow banks, or even the puddle that builds up at the serwer intake on the road? or whould i swerve to miss those?....lol
I just want to know what kind of stuff to look out for..
|10-12-2008 03:41 AM|
|Triple88a||btw dude welcome to the turd axles.|
|10-12-2008 02:22 AM|
|10-12-2008 12:24 AM|
Ok so i went over to my brothers and we crawled under there so he could tell me how screwed i was ....
He said im leaking what seems to look like "gear oil" from my ... i want to say "marion housing???"
He pulled his finger out of that area and showed me something red. and said that someone had been in there before because he has never seen a red seal from a factory.
Now i love my brother and all but does he know what the hell he is talkin about????
im sure i sound like a total jack ass with that one..
Should have worn my helmet when my short bus rolled over huh....
And i did find that my gearing is 3.73 on the 31"s
|10-10-2008 03:37 AM|
|CVFD76||but dont trust fully wat it says, iv read on here somewhere where a few people pulled their diff apart and the gears were different than what the tag said|
|10-09-2008 11:14 PM|
The gear ratio is stamped on this tag. Its just under the layer grime.
|10-09-2008 10:59 PM|
yeah the tires are 30/9.5
I will have it checked out. Do you think it is a major problem?... something i can put off till the weekend?
|10-09-2008 09:37 PM|
|Hebera||If your Jeep came with the big wheel package 30x9.5 then your gearing should be 3.56 if those tires are 235/75/15's then your gearing should be 3.07 Jeeps in general have a very low first gear, this being your first Jeep you might not have realized how low it is. Cruising at 70 your RPM's should be in the 2000 -2300 range, thats how my Jeep was, I had the big wheel package on it and 3.56 gears with the 5 speed. Yes those oil marks are not normal and if you still have the warranty I would get it checked out. Hope this helps|
|10-09-2008 09:34 PM|
Perhaps the oil comes from a leak at the pinion where the front driveshaft is attached at the transfer case.
Is there enough oil in the TC? Park the TJ on levelled ground and open teh fill plug (you can see it on the pic below). The TC must be filled up to this plug.
|10-09-2008 09:28 PM|
Well first off.... i dont know squat about mechanics YET...lol
Here are pics of what i see.
I'm going out on a limb and guessing that the oil like substance to the left of the transfer case is not normal???
I dont know why its there... but it looks fresh. Any ideas? I did get a power train warranty with the jeep so if need be i can fix that if its a prob.
|10-09-2008 08:11 PM|
|slf41002||If he has granny gear in first i would say that he has way lower than 3.07 and more than likely lower than 3.73.I would say either it has been regeared or if not a Rubi has the 4.1 mod on the t-case.If it is a Rubi it does have the 4.1 ratio t-case.I think that is correct as mine unfortunately isn't a rubi just a diamond in the rough.|
|10-09-2008 07:18 PM|
Your gearing is either 3.73 or 3.07. If your rear axle's differential cover is perfectly oval-shaped with a black snap-in cover in the lubricant fill hole, it's a Dana 35c. If the cover is more stop-sign shaped and more angular, not oval-shaped, with a threaded steel bolt in the lube fill hole it's the stronger Dana 44.
What are your rpms at 70 mph and what size tires are you running?
|10-09-2008 06:53 PM|
any way to tell what ratio im running from those numbers?
And what RPM should be my cruising speed?
Yeah i know... damn does this guy know anything?...lol
|10-09-2008 01:15 AM|
|jeepincj7930||i have a 6 speed but my first gear is the same way i usually start in 2nd|
|10-09-2008 01:13 AM|
Yet another thread from me. Pretty soon i just might know something about jeeps...lol
So i have a 99 Tj 4.0 5speed.
This is my first jeep so i wasnt sure if i should have low gearing.
1st is almost like a granny gear.
I went and looked at the read transfer case and could only make out these numbers stamped in it.
The dana logo and then these numbers.
Make any sense you anyone?
What gearing am i running and what rear axel ?
I tried to find anything that looked like a tag but there was none. Just the stamp in the back.