Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Lowering Axle to Install Springs

Join Wrangler Forum Today


Thread: Lowering Axle to Install Springs Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-22-2012 07:51 PM
UnlimitedLJ04
Quote:
Originally Posted by umake View Post
Huh, didn't know that. Guess I need to order some new ones then. What is recommended?
make your own...not real hard...only talking 1/2" difference...
08-22-2012 07:43 PM
umake Yup, this will work but the lower sway bar bolts are seized. Need to break the nut off the bolt tomorrow. Not a big deal, got JKS Quicker Discos to install anyways.

Quote:
Originally Posted by UnlimitedLJ04 View Post
make sure to remove the bumpstop cup and jounce bumper, will make life easier. don't forget the bumpstop extensions in the rear...OME includes 0.8" extensions, but they aren't enough, 1.25" are minimum for OME's rear shocks...
Huh, didn't know that. Guess I need to order some new ones then. What is recommended? I see the JKS ones on Quadratech...maybe I'll order those.

http://www.quadratec.com/products/16159_110X_PG.htm

Thanks for the help everyone.
08-22-2012 06:38 PM
UnlimitedLJ04 do not unbolt the lower or upper control arms (unless replacing the arms). you'll have a hell of a time getting them back in, especially in the front.

however, before you lower the axle, you do want to loosen the bolts. remember to torque them after the weight is back on the tires. you can look up the torque specs for everything over on JeepForum.

make sure to remove the bumpstop cup and jounce bumper, will make life easier. don't forget the bumpstop extensions in the rear...OME includes 0.8" extensions, but they aren't enough, 1.25" are minimum for OME's rear shocks...
08-22-2012 06:32 PM
kjeeper10
Quote:
Originally Posted by TnDz TJ

Yup...

http://www.wranglerforum.com/f5/tera...urs-99763.html

yeah... you are fine.... you just need to jack the opposite side up from the one you are working on.... I would hook your lower arms back up though....
08-22-2012 06:29 PM
TnDz TJ
Quote:
Originally Posted by kjeeper10 View Post
You did a write up awhile back huh ?
Yup...

http://www.wranglerforum.com/f5/tera...urs-99763.html

Quote:
Originally Posted by umake View Post
Are my steps above correct? Its the only way I can see to get the springs into place at this point.
yeah... you are fine.... you just need to jack the opposite side up from the one you are working on.... I would hook your lower arms back up though....
08-22-2012 06:16 PM
umake Gottcha. Thanks guys, off to give it a shot.
08-22-2012 06:13 PM
kjeeper10
Quote:
Originally Posted by TnDz TJ
If you have the frame high enough on stands.... droop the axle with all the control arms on... then jack one side as far as you can and slide the spring in on the opposite side.

I used ramps on opposite corners and never needed a spring compressor....

It forces a droop when you do it this way....

works on the front the same way...

I did this with a 2" BB early last year, but it works for springs too....
You did a write up awhile back huh ?
08-22-2012 06:12 PM
kjeeper10 You really only have to disco the sway bar links shocks. Jack frame up then axle. One tire at a time (the side your working on.
Worked for me.

Spring fell right out.
08-22-2012 06:12 PM
umake That's a clever way of doing it. Never thought of that.

The jeep is as high as my floor jack would take it and no droop. Its on 6 ton jack stands but I still can't slip the springs into place with the compressors almost fully compressed.

Are my steps above correct? Its the only way I can see to get the springs into place at this point.
08-22-2012 06:06 PM
TnDz TJ If you have the frame high enough on stands.... droop the axle with all the control arms on... then jack one side as far as you can and slide the spring in on the opposite side.

I used ramps on opposite corners and never needed a spring compressor....

It forces a droop when you do it this way....





works on the front the same way...



I did this with a 2" BB early last year, but it works for springs too....
08-22-2012 05:55 PM
umake
Lowering Axle to Install Springs

I found a write up on the Cherokee forum (similar suspension by the looks of it). Got my old springs out with compressors, but I don't see how I can get the new 2" OME springs in without lowering the axle. I've compressed them but they still won't slip into place.

Just checking to make sure I have the right steps before I get going:

1. Unbolt sway Bar
2. Unbolt shocks
3. Unbolt lower control arm (only the side I'm installing)
4. Put spring in place

Is that it?

Hoping to get the front springs on tonight and start on the rear tomorrow.

Thanks for the help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:09 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC