|08-05-2014 02:08 PM|
|Bearfan||Doesn't show up in my iPhone, I'm using the app. I guess not everything is viewable from mobile devices. I haven't used my lap top in months.|
|08-05-2014 01:03 PM|
|08-05-2014 10:56 AM|
|Bearfan||Anyone have this PDF they could post?|
|08-04-2014 08:25 PM|
|Bearfan||Does anyone have the PDF write up on this? It's no longer available. I'm installing my soft top this weekend. Thanks|
|07-30-2014 01:30 PM|
Here is a nice video showing the same thing - might also be helpful.
|07-23-2013 08:45 PM|
|dgallois||Most excellent write up. Good job and thank you.|
|07-17-2013 02:26 PM|
Thanks to the op. I just used this guide last night. Awesome! Thank you so much.
|06-28-2013 08:25 PM|
1x MOPAR 55397228AB - MOPAR® Passenger Side Soft Top Bow Bracket for 07-10 Jeep® Wrangler Unlimited JK 4 Door - Quadratec
1x MOPAR 55397229AB - MOPAR® Driver Side Soft Top Bow Bracket for 07-10 Jeep® Wrangler Unlimited JK 4 Door - Quadratec
4x MOPAR 6503259 - MOPAR® M6 x 1.25" Round Head Screw for 07-13 Jeep® Wrangler & Wrangler Unlimited JK - Quadratec
|06-28-2013 07:45 PM|
|06-28-2013 03:19 PM|
|06-23-2013 11:02 AM|
|kpurcell1466||stellar guide!!! U are a asset to the jeep community!!!|
|06-16-2013 10:11 PM|
Here you can get the ones for the 2013 and the bolts too.
Soft Top Roll Bar Brackets 97 - 2013 TJ JK
|06-16-2013 09:00 PM|
Thanks--this helps allot --i figured the pre '13 brackets wouldn't work. Now i know for sure.
Next i need to find a dealer that understands.
If anyone has the part numbers let me know.
|06-16-2013 06:49 PM|
|jwilson2598||You're missing the roll bar brackets. You need to get them from the dealer, and they are 2013 specific as that was the first year of the spring assist mechanism, which uses different brackets. You'll need the left and right brackets, 4 bolts to attach the brackets to the roll bar, and 4 bolts to attach the top to the brackets.|
|06-16-2013 06:41 PM|
Guys--thanks for this thread and the PDF. I've searching everywhere even called two separate dealers to ask about the soft top bow brackets. (they seem to know nothing)
I have a 2013 4 door that only came with the hard top. I purchased a 2013 premium soft top on CL and need to determine if i need brackets to attach the top and what the part numbers are.
Here's a pic of the top---if anyone can tell me if i need brackets and the part numbers it would be great. If you have a picture of the 2013 bracket that would also be helpful.
|06-15-2013 08:52 AM|
Thanks so much for taking the time to make this tutorial. I spent a couple of hours trying to figure out the soft top installation myself (Jeep should be embarrassed by their manual), and then another hour or so searching the Net before coming across your guide.
To me, the most confusing part was how to install the rear window tension bar clips. Your photos immediately solved that dilemma for me. My soft top is fully installed and ready to roll. To anyone who may be feeling discouraged about switching tops, this guide makes the process ridiculously simple!
|06-02-2013 07:30 PM|
|06-02-2013 01:12 PM|
|Sol||I haven't tried it yet, but was wondering if, instead of getting someone to push down at the rear, could you attach a couple of tie downs to the cage and the rear seat anchors and apply some gentle tension? I have a 13 2 door dual top.|
|05-07-2013 08:18 PM|
|Toucan Sam||Great instructions - thanks! Just installed the softtop for the first time, just needed a 2nd person to push down on the rear top so I could get the rear flaps hooked on.|
|05-07-2013 07:28 PM|
It is tight getting the sides zipped but it is much better this way. Will supply pics if needed. It is dark right now though.
|05-07-2013 06:45 PM|
|jwilson2598||Panter, my rubber flaps also stuck out from being packaged up. I took my time and held them as flat as I could and shut the tailgate on them. After. Week or so they had laid themselves down and now are fine. Same with the window bar itself, super tight at first, but now I can remove and replace it a bit easier.|
|05-06-2013 09:59 AM|
Great write up!
I finally got my hoist built, my spiderwebshade on, and the soft top installed (kinda).
I see that I have to go redo my rears where they tuck into the doors.
Also, I'm not sure if my window bar is installed correctly. The two rubber "corners" that stick out seem to stick out pretty far.
What a pain in the arse....and getting to my cargo area with a Tuffy enclosure is now impossible without removing the rear window. I guess that makes it nice and secure.
|05-06-2013 09:41 AM|
|jdambm||subscribed if it ever stops raining|
|05-06-2013 08:29 AM|
|Jerkstore||I finally raised the roof: removed the hard top (now resting on DIY cart) and installed the soft yesterday. Amazing that an iconic manufacturer can produce so many reams of useless manual pages - plus irritatingly scored videos - while a couple dedicated drivers can produce and openly share clear, easy-to-follow guides. Score a big one for the drivers - and THANKS to the drivers on this and other threads.|
|04-16-2013 12:16 AM|
|04-15-2013 11:59 PM|
|roadking40||Just spent the last 90 minutes "installing" the soft top on my 13'. Still don't have it on. The rear sails are WAY to far from tucking in. Clearly Jeep wins the most fxck'd up design award.|
|04-08-2013 07:37 AM|
Thanks all. I know where to come to get the skinny on all things Jeep.
|04-07-2013 11:07 PM|
|04-07-2013 10:41 PM|
|jwilson2598||There is a slot there to roll them into , if you just tuck them into the door like you have it now, they'll pop out at speed.|
|04-07-2013 09:42 PM|
Awesome stuff. Saved me a lot of headaches. It was not easy, but I'm jumping the gun here a bit. Was only 45 degrees and the top was very tight. But, with some help I got it on. Only part I still question is the side windows. Does the L bracket just sit inside the frame for the back door? Or does that get rolled under into a slot in the frame similar to the sail panels? Right now they are just sitting inside of the frame, but that doesn't seem right or secure/ tight enough.
|This thread has more than 30 replies. Click here to review the whole thread.|