Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Drift Shaft problems

Join Wrangler Forum Today

Thread: Drift Shaft problems Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-04-2012 04:53 PM
soad334 I figured it out, the u joint that connects with the rear dif has enough play for me to be able to move it by hand (and is the source of the noise). I've got new spicer's on the way (hope it makes it) I'm gonna take a look at all of them though just to be safe. Thanks for the help everyone!
09-03-2012 12:08 PM
ciamex do you have an upgraded front diff?

mine is always locked so it complains under tight turns...
09-03-2012 10:41 AM
TnDz TJ When warm does sound odd.... if the joint is bad... its bad.

To side-load the joint... you must be able to put pressure on the caps. using a prybar between the bottom of the knuckle and the joint, apply pressure upward on the cap and watch for play INSIDE the joint by the seals. You need to rotate the shaft 90 degrees to check the next one... then again... and again. Move to the other side.

If you find no play, it doesn't mean they are good.... they could be dry as a bone and seized.

Your best option is to pull the shafts and fully inspect them.... new Spicers are only $22 each here... FYI
09-03-2012 09:29 AM
269jeep When it's warm sounds odd. I would still check the axle joints. Take a pry bar and try to move the the axle shaft. If you are new to working on Jeeps get yourself a good manual. Haynes and Chilton manuals are available everywhere. These are ok. Nothing beats a factory service manual if you can find one. This forum is a great place for tips too.
09-02-2012 11:58 PM
soad334 oh and I should mention this is only when warm, not sure if that matters
09-02-2012 11:49 PM
soad334 Sorry noob here but "side-load"? and should I raise it on jack stands when I check for play?
09-02-2012 11:09 PM
TnDz TJ When turning, what you are hearing the axle shaft u-joint(s) within the front knuckles. Visually inspect them, you may not see using a prybar, you can side-load the u-joint and look for play.... you most likely will find it in one or both joints. You must check all four endcaps for play.

I had a tight ujoint.... no play at all, but when I removed the axle shaft, I could make it bind by working the joint.
09-02-2012 07:57 PM
Drift Shaft problems

I Have a 97 TJ 4.0L engine and I have an issue that whenever I turn AND accelerate (reverse or drive from being stopped) I hear a load obnoxious clicking/popping/groaning sound. From what I've been reading I'm figuring either bad u-joint or cv joint but I don't really know what the difference between the two are or which one is the culprit.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:18 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC