Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Need advice removing 3" body lift

Join Wrangler Forum Today


Thread: Need advice removing 3" body lift Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-12-2008 03:51 PM
Triple88a man with 7" of lift on my TJ i'd be able to fit 38ts and still have plenty of flex
11-12-2008 11:51 AM
WhatHuhWho Thanks for the heads-up on the bolts-

Last night had it out in the woods and was all mudded up- even for me its a pain to get in when everything is slimy. But, deer season is approaching here in MO, and the woods are calling. The body lift is going to be a winter project of mine. Ya gotta love how those big tires roll-- no trails needed. I love my Jeep!
11-11-2008 08:16 PM
Triple88a 2x on that, i have seen many people break the nuts off from the body especially with 3" body lifts. The nut looking things are welded to the body from the inside. Once the bolts rust to the nuts and the welds holding the nuts rust as well. That can easily brake which will put you into a big trouble. The main reason for these damages are common on 3" bls is because the 3" pucks need longer bolts. The longer bolts have more leverage. The pucks can only hold the body in place so much but with the lots of leverage, the bolt bends the nuts left and right to where it eventually cracks the welds.
11-11-2008 08:03 PM
scrambler1 Make sure you take your time and spray what you can down with penetrating oil a few days before. then use a little heet if needed to loosen the bolts going into the body. They can break quite easily,poor design.
11-10-2008 09:22 PM
whiteyj This was one of my selling points for rocker knockers (w/ sliders rails). It gave the Mrs something to step on.
11-10-2008 06:52 PM
Coyote_94YJ or a rope ladder like they use on helicopters.
11-10-2008 06:25 PM
Triple88a i would replace it with 1" daystar bl as Coyote recommended above... You get almost all the bolts you need and you can replace your old rotten bushings. I doubt they will make much difference in handling.

If the wife has problems getting in, get her a step. She will like it better as it will be much lower than trying to stick the foot in the door.
11-10-2008 06:00 PM
Coyote_94YJ You might notice a bit better handling but not much. It is a brick after all. With your 4" suspension lift and 33's I think you'll be fine without the body lift. But that is entirely up to you. You could get the daystar 1" body lift. It incorporates the mounting bushings with the lift all in one.
11-10-2008 04:41 PM
WhatHuhWho Will this drop help the highway stability? Other than the big step up and in for my wife-- will this drop be worth my time?
11-10-2008 02:41 PM
Coyote_94YJ Look to see if the fan is going to rub on the fan shroud. You might have to make an adjustment to the shroud. I would pull up the shifter boots and see whats been done there. Most likely nothing but its worth a look. The steering linkage should move freely.

The most important thing to look for with a body lift that high is damage to the body tub where the mounts are.
11-10-2008 12:04 PM
WhatHuhWho
Need advice removing 3" body lift

What do I need to look for when I decend my ride? It should be simple, but want to avoid potential hazzards. Steering? Trans link? Anything? I have an '89 Laredo with a 4" suspension and 3" body lifts. I've looked, measured, and my 33X12.5's will fit w/o the body lift. My wife hates climbing in it too! Straight 6, 5speed. Appreciate the help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:06 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC