Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > installing lights on stock bumper

Join Wrangler Forum Today


Thread: installing lights on stock bumper Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-19-2008 12:09 AM
jp'rs_peep'rs Actually,
the most recent lites I just put on (about 2-3wks. ago) came with 30amp sw.
Even tho this was the case I still chose to have relays.

C.
11-18-2008 03:26 PM
distortedtj Whats your budget?

Also you do not have to run the negative light wire to the battery. It can be grounded anywhere to the frame or body. No need to run more wire than needed.
11-18-2008 02:50 PM
XNeoJesterX Thanks I forgot about the relay. It's been about since I wired lighting, but its coming back to me.

Any recommended brands/models that are high quality BRIGHT lights that are reasonably priced cause I am trying to keep the cost to a minimum?
11-18-2008 01:12 PM
Atthehop All the kits I have seen have very detailed wiring diagrams. Make sure you use a relay to turn them on and off. With a relay you run power from the battery to the relay and from the relay to the lamps then ground. Now you wire the switch to the relay. This way when you turn them on you do not send all that juice through the switch which unless it can handle it will burn out.
11-18-2008 12:20 PM
XNeoJesterX eh I don't think I'll go the wireless route, even tho that remote setup is pretty sweet. I'm just gonna use a switch on that panel above the dc outlets. I still need to figure out how I'm gonna run the wires and what lights I'm gonna get. You run the positive from the battery to the switch with an in-line fuse. Then from the switch to the lights and the negative from the battery to the lights right?
11-18-2008 11:30 AM
Atthehop I don't remember where I got mine 4 years ago but these look very close to what I have. Switches - Pilot 4 Channel Wireless Remote

They work great.
11-18-2008 10:15 AM
XNeoJesterX ohio luckily doesn't have state vehical inspections. Can you link me the wireless remote and do you have it on the switch panel? If I run wires for a switch were is the best place to get thru the fire wall? Thanks for the input so far guys.
11-18-2008 10:10 AM
TJDave Not sure about Hella's, but for my KC's I had to bore out the holes on the bumper to fit the lights on. I mounted the switch on the flat panel that sits next to the rear wiper/defrost/OD switches. I think that is where an ashtray would go If I had one.
11-18-2008 09:01 AM
Atthehop I installed the Hella Black Magic kit with a wireless remote to turn them on and off. Plus I wired then to come on as I need and not go off with the high beams as required in NJ. It's simple to make them legal to get through state inspection.
11-18-2008 08:46 AM
richp The holes should be the correct size. The hella kit will come with a relay, wire and switch. When I added my Hella 500's I just drilled a hole in one of the empty switch blanks and mounted it there. Once I ran the wires I used some split wire loom to encase the wires. I did built a small L shaped bracket out of some sheet metal from a pc case, the metal thats used to cover the full drive bays on a tower case, that is mounted next to the PDC on the passenger fender to mount the relay.
11-18-2008 06:56 AM
XNeoJesterX
installing lights on stock bumper

i want to put hella or similar lights on my stock front bumper. I was wondering do I use existing holes on the bumper to mount them? Also I was wondering the best way to run the wires so I can put the swith on the switch panel above the dc outlets. Is there any factory stuff, at least wiring or switches I can use or get from a 'stealership'? Any pictures would be appreciated. What are good lights for a reasonable price? I've heard of KC daylighters and Hella.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:11 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC