|10-04-2012 12:14 AM|
I started out with a full width
And ended up cutting it down to a mid with a year later
Lights haven't even crossed my mind lately. I did upgrade the bulbs in the headlights right after I got the jeep, but that is it. I have had my mind on other parts of the jeep to think about lights much.
|10-04-2012 12:13 AM|
|10-04-2012 12:09 AM|
That's what I was looking for when I bought my bumper. Got the Rockhard 4x4 full width because it gave good protection across the front of the jeep. Had fog light inserts and the winch mount sits down low in it. This does two things, keeps the winch from blocking the radiator (not that big of a deal) and also covers up most of the winch so it is better protected from the elements and such.
The thing is super tough, but the drawback to that is that it is a heavyweight.
|10-04-2012 12:06 AM|
|Lowerumble||Offroad and rock climbing only? I would defintely look at a stubby. I like the poisonspyder and jcroffroad stuff. I would have loved a stubby, love the look and function(even if I don't need it yet!), but I settled on a JCR midwidth with prerunner bars because ultimately(much to my chagrin) my jeep will actually spend 99% of its time onroad. I will only get to wheel it on the weekends, and then only select weekends at that so ultimately I determined that the protection that the midwidth offered was far more important, but with a midwidth I was getting a little closer to what I would have ultimately wanted.|
|10-04-2012 12:00 AM|
|10-03-2012 11:59 PM|
|10-03-2012 11:56 PM|
|Farnham21||I never hear much about anything but ace rock rails|
|10-03-2012 11:54 PM|
|10-03-2012 11:53 PM|
|pluke the 2||A bumper and a winch ain't going to fix a broken engine or oil pan on the trail.|
|10-03-2012 11:51 PM|
|WatchThis!||What do you want out of a bumper? Because that is a tough one. It took keep 3 months to make up my mind on my front bumper. Then I went and cut the thing up a year later.|
|10-03-2012 11:50 PM|
|pluke the 2||
Winch and Bumpers are not in my field of expertise.
I'd suggest you consider a transmission skid first and an oil pan skid plate second and a evaporation can skid plate or relocation.
Fourth, rock rails. Not Rubicon rails. Sell them.
|10-03-2012 11:46 PM|
|emonty13||Haha...well, my budget is set for the next year, then--any suggestions on the bumper, perhaps? I might want a winch before I change out the axles... :P|
|10-03-2012 11:26 PM|
|pluke the 2||
Lose the electronic disconnect and install either an anti rock or disconnects.
Don't upgrade the 44. Go straight to a 60. Don't buy 35s off the bat, get 37s as a minimum.
Get a long arm with a stretch kit and some coilovers. 1310 drive shafts.
|10-03-2012 11:23 PM|
New 2012 Rubicon, mod suggestions
I'm looking for some advice with my 2-dr 2012 Rubicon. The first aftermarket thing I want to replace is the bumper and that awful rubber cover and get a winch installed. I'm stuck between replacing it with a full or stubby bumper--I plan on mostly using my Jeep for off-road and rock-climbing, and cost isn't it a huge factor. Still, I think I'd prefer a full bumper just because of nose on nose Forest Service road ding with a Tacoma that I suffered about 3000 miles into owning the Jeep (both our faults)--I realize I'm a bit gunshy on keeping the wheel-well open after this, so talk me down if I'm an idiot for still preferring a full bumper to a stubby. I've also noticed that some full bumpers don't have light cut-outs--are there decent mods or is there any advice for either creating cut-outs or moving the fog-lights?