Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Heater issue

Join Wrangler Forum Today


Thread: Heater issue Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-15-2012 09:54 AM
pberg
Heater on and off ?

Hi, I have read this thread and have a related question: Jeep wrangler sport 1999.
Heat works intermittently and doesn't respond to the dials. Sometimes it gets nice and hot and then won't shut off and other times doesn't work at all. Plenty of coolant and no apparent leaks. ??
I really want to fix this myself but am not sure what is going wrong, ideas?
11-30-2010 10:31 PM
mike_the_engineer Also, run the water in the opposite direction that it normally flows. So spray water into the outlet pipe and whatever crud is in there should come out of the inlet pipe.
11-30-2010 09:59 PM
mike_the_engineer
Quote:
If I held the RPMs up for awhile I'm assuming the outlet hose would also be hot
Yep. In fact, it should be hot at idle if the heat is on.

Quote:
Perhaps there is a blockage and whenever I ramp up the RPMs it gives the coolant enough pressure to push past the blockage and bring back the heat?
That's exactly what's happening. And like jason said, it's probably your heater core that's clogged. That's a really common problem and you can flush it with a garden hose. Just pop off the two heater hoses where they connect at the firewall and run some water through it. Just be careful when you do that. The core is somewhat delicate and it isn't built to handle a lot of pressure. If you rupture it, you have to take the entire dash out to replace it. Not fun. If all goes well, the entire job shouldn't take more than 15 minutes.

A few tips:

1) Wait until the engine is cool. Getting sprayed with hot antifreeze sucks.

2) When you pull off the hoses, coolant is going to go everywhere. Have a bucket handy.

3) Don't leave used antifreeze laying around. It's highly toxic. Dogs will drink it because it smells sweet, and if they do, they'll die. Painfully. Make sure you clean it up, recycle it properly, blah blah.

Best of luck!
11-30-2010 09:20 PM
jasonwrangler heater core is clogged up, try flush it.
11-30-2010 09:02 PM
MrMiyagi Only residual heat. As soon as I let off the RPM it stops blowing out hot air. Just some more info:

Coolant level is OK

Inlet heater core hose is hot, outlet heater core hose is cold (this is at idle. If I held the RPMs up for awhile I'm assuming the outlet hose would also be hot)

So...this could call for a flush?

I'm not sure how the vacuum system or water pump system works on the jeep. Perhaps there is a blockage and whenever I ramp up the RPMs it gives the coolant enough pressure to push past the blockage and bring back the heat?
11-30-2010 08:49 PM
jasonwrangler once you get heat but the RPM goes below 1k do you get heat?
have you check your coolant level?
11-30-2010 07:46 PM
MrMiyagi
Heater issue

Hey guys,

Couldnt find a thread that helped me out. I have a 2006 TJ and the heater isn't working correctly. When I let the jeep sit idle and reach operating temperature with the heater on, there is no heat. Only until I start driving and run at RPMs over a grand will the heater kick on. I'm guessing this isn't electrical and has something to do with my vacuum tubing? I checked some of the connections that were easily reachable but didn't want to proceed any futher unless I had someone to back me up that I was going in the right direciton.

Any help?

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:19 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC