Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > trans swap question

Join Wrangler Forum Today


Thread: trans swap question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-18-2012 04:30 PM
Acwhit Just wanted to thank you all for your advice.
Engine rebuild is done...just have to wait for the trans. to be done now.
Trans shop has located one and is now negotiating $$. Hopefully it will be done soon, I just want to be able to drive it again.
10-17-2012 12:58 PM
Tyewilly Good reading
http://www.novak-adapt.com/knowledge/ax15.htm

And this
http://www.novak-adapt.com/knowledge/ba10_5.htm
10-17-2012 12:43 PM
Beachcruiser You do NOT need one from a 4.2 motor. Any jeep AX-15 will work fine, tho you might have to juggle some things like pilot bushing size & clutch slave cylinder parts.

Your best/easiest bet is to get the entire bellhousing/tranny/T-case from a 90-92 Wrangler...as those years involve the least work to convert (they are a virtual bolt-in swap).

There are plenty of write ups on this swap....I suggest reading a bunch & printing one out to take in to your mechanic.

BTW, be sure to use a clutch for the 4.2 flywheel...NOT one for a 4.0/AX-15.

I did the same swap for under 500, total.

FYI ~ the back of the bellhousing pattern is different from your current set up. As is the input shaft to the T-case, and the speedo drive on later YJs w/ the AX-15. (these are the main reasons why the years mention offer the least hassle)
10-17-2012 12:43 PM
Acwhit Thanks!
Guess I should've mentioned...I was starting to have problems shifting, it was starting to get to jam it into gear until it warmed up.
As far as I know, the bell housing is different.
10-17-2012 12:34 PM
sevenservices Welcome!

personally, I say leave it in the jeep and start hunting for an AX15. Why replace it if its not broke? Yeah, maybe its a harder breed to work on but shoot, at least run it until it dies. Just 'cause the engines out doesn't meen its all that easier to change the trans. Especially at a shop. Maybe if your using a block & tackle pully out in the backyard from a tree it might be easier to just pull it once but heck, in a shop you can pull a tranny out the bottom and not even move the engine. You'd actually support the rear of the engine so it doesn't move.

I dont know for sure if a 4.2 and a 4.0 are the same rear trans bolt pattern but if they are different you'd think it would only be the bell housing that is different. Those can be replaced, Not sure though...

just my opinion...
10-17-2012 12:16 PM
Acwhit
trans swap question

I have a 88 4.2l Having the engine rebuilt because it was spewing oil everywhere. While that is being done we decided to have the trans checked out. Trans shop says we have a peugeot trans that is garbage, can't get parts etc. They tell us we need to get an AX 15. Fine, but then they tell us they're having a hard time finding us the right one, that it has to be from a 4.2l or it's a lot of work to swap, I think they've found one but it's $900 I think... I've found a couple that were from a 4.0l that were reasonably priced, $350-500.
I just want to make sure that we're not taken advantage on this because we brought it in to get it repaired.
Thanks for any advice!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:29 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC