Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > help me please need as many jeep gurus as possible

Join Wrangler Forum Today


Thread: help me please need as many jeep gurus as possible Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-07-2012 11:10 PM
correycinciyj wait im confused. why wouldnt i hook up the one behind the dash.? i took almost every single electronic part of the 93 and put it in my 89. engine, the entire harness, both computers(behind glove box and also below brake booster), evap canister, fuse box under the hood, the entire dash and gauges, also the ducts for the heating(heater core and blower motor). the only things i left are the A/C system and ABS pump. the only thing that is still 89 is the steering column but i swapped that and tried a new ignition switch and it didnt change anything.

good to see you jumping in here BIG. ive seen a lot of your stuff and its been very helpful..
11-06-2012 01:21 PM
Ibuildembig First of all, the ecm behind the glovebox shouldnt be in there or hooked to anything. Are you using any of the 89 harness? I am thinking neutral saftey/clutch switch.
11-06-2012 12:29 PM
correycinciyj ok so i tried the new ignition switch and no luck. i also grabbed the steering column from the 93 thinking it might not be compatible and that didnt work either. im at a loss right now. my thoughts are clutch safety switch, neutral safety switch or just the computer all together. has anyone done this?
10-31-2012 06:49 PM
correycinciyj well i just so happen to have a new ignition switch in the garage that i bought just in case a few months ago. ill take a look in that area. do i need to remove the column to install the new one. if so that sucks. i just put it back in. also just saw this. the column i have in it is my 89 one. it has a group of wires that go to the wiper delay, but there is a second clip that hangs down. (not sure what they are) anyways the clip that comes from the harness plugs right in however the harness has one extra wire that goes to nothing in the column clip. do these wires have anything to do with ignition or is that just the ones that go to the ignition switch?

thank you to anyone that jumps in on this help thread. its been parked for months now and need it back for the snow.
10-30-2012 08:39 PM
Hailtothevictors Ignition switch or wiring? i just had a problem with mine. If you can turn the key to the on position and fire up the engine by connecting the circuit between the two screws on the starter then that could be your problem. I just used a long screwdriver and touched it to the two screws and it would spark some and start the engine. it doesnt put out enough power to hurt you but just be careful of fire. i had to use this method for a couple of days and was fine.
10-30-2012 08:36 PM
harleydragon if it cranked and ran then you don't have any big problems...check your ignition switch to see if you have a wire that gets hot only when you turn the key all the way to start...if so then run that wire to your starter solenoid...your problem may be something as simple as the switch that says your tranny is in park
10-30-2012 08:35 PM
correycinciyj i kinda had the same thought but have a problem there. the ax i have came from a 94 cherokee and has a 2 prong clip coming from it. the harness that i now have from the 93 has 4 ity bity prongs and is for an auto trans.
10-30-2012 08:31 PM
correycinciyj no. if i turn it forward i can hear the fuel pump kick on behind me, the computer in the engine bay kinda whines a little and i can hear i believe 2 relays clicking in the fuse box under the hood but thats when i go to turn the key to the run position. but will not crank the starter.
10-30-2012 08:28 PM
rykemc Reason I ask is I swapped in an AX15 into my 88 and did away with the wire loom that connected into the transmission. Still had the harness coming from the trans but the harness it plugged into I tossed. We could not get the key to engage the starter. Acted like a neutral safety switch problem. Found the harness that plugged into it and plugged it in. Presto, engine fired and started. Look at that area.
10-30-2012 08:25 PM
rykemc Let me ask, will the key engage the starter?
10-30-2012 08:18 PM
correycinciyj
help me please need as many jeep gurus as possible

ok so ill give a little background on the jeep.

i have an 89 wrangler islander. originally a 4.2 with a BA trans. PO butchered it by putting in a 4.0 in and slapping a carb on it from a 75 ford pickup. no sensors were hooked up. i dont even know how he got the thing to run. anyways that engine died and now im swapping everything over. im making it all 93. i found a 93 wrangler 4.0 with an auto.
currently the engine is mated with my AX-15 and in the 89. the entire harness is in, the computer below the washer fluid is in. and the one behind the glove box is installed. IT WILL NOT START. after some research i found that i needed a crank position sensor(CPS) to work with the AX-15. put that in today and still wont start. i thought it may have been my starter so i touched the post together and it cranked. just wont work from the key. now im reading that since the computer is programmed for auto that there is no way it will work with my current set up....... what do i do. please help me someone

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:19 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC