Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Front Diff Locker Relay

Join Wrangler Forum Today

Thread: Front Diff Locker Relay Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-12-2012 10:01 PM
DLJ Yea I was able to grab a rubi d44 front axle and I going to swap out my d30 with it thats why I ask. My Jeep is an TJ/LJ non rubicon so I doubt it has the rubicon wiring harness. It would be nice if I could find a way to wire it so the sensor works with my cluster light but from reading what you replied it would be pretty difficult. Thanks for the input!
11-12-2012 07:58 PM
Jerry Bransford The locker lights in the instrument cluster are controlled by the computer & I never bothered to get that deep into the circuit. It'd probably take some 5v logic-level voltage work to trick the computer to illuminate that light since the computer also checks around to make sure everything is working as the computer expects it to.

My TJ is a Rubicon so I left that part of the circuit connected so at least my dash locker lights flash while the lockers are on. I only rewired the part that controls the two compressors controlled by the pair of on-off switches added to the dash where the ash tray used to be. I had to rewire it since that part of the circuit wasn't working when I bought the Rubicon used.

If your TJ came with the Rubicon wiring harness connectors that plug into the top of the Rubicon axles, and I would bet they are there, I'd plug the front axle connector into the top of the new axle. At the least it would probably cause the dash light to slow-flash when the new locker is enabled. I don't mind that my locker lights never stop flashing while they are in use... it kind of serves as a reminder to shut them off when not needed.
11-12-2012 06:35 PM
DLJ Oh ok. Do you happen to know about how to wire the sensor from the axle to the cluster so the FRONT AXLE LOCK light is on? Thanks
11-12-2012 06:10 PM
Jerry Bransford You don't need a relay to wire the Rubicon compressor. All you need to do is to provide the compressor a source of 12v that you wire an on-off switch into. Turn the switch on, the compressor turns on & locks the locker. The compressor has an internal switch to shut itself off when the required air pressure has been reached. The compressor doesn't draw much current, my two Rubicon compressors are protected by a pair of 5 amp fuses.
11-12-2012 04:58 PM
Front Diff Locker Relay

Does anyone know where I can get a "Front Diff Locker Relay"? I need it to install the oem rubi lockers. Also does anyone know of any write ups on how to wire up the rubi locker? I already tried looking around for the wiring of it but could not find good info. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 04:39 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC