|12-12-2012 10:51 AM|
|hawkpilot60||RockAuto has the for $65|
|11-15-2012 09:33 PM|
|11-15-2012 06:47 PM|
|Mom sold the Jeepster||The camber angle is off, or does the tread wear look like that? Have you checked the front axle u-joints for excessive play? Jack it up and rotate the wheel to see how much play there is in the joint before the axle shaft starts to turn.|
|11-15-2012 06:23 PM|
|derf||Good to hear.|
|11-15-2012 06:14 PM|
|3JKs1H1||Unit bearings at 32K miles? Unless you drive in a lot of streams you should get 100K+ out of those.|
|11-15-2012 05:59 PM|
|11-15-2012 04:45 PM|
|burton861||So I got new unit bearings on each side and my tires are straight as an arrow!|
|11-13-2012 03:43 PM|
|derf||Of course, my input is only speculation. It's impossible to tell by just what is said on a message board. I only suggest a bent axle as a possibility. There are as many truss/reinforcement kits for the front axle on the JK as there are for the TJ. Probably for a reason. The best course of action for the OP would be to give it a thorough inspection and alignment to see what is actually wrong with the Jeep.|
|11-13-2012 01:36 PM|
I am not a JK guy...but I am gonna second the ball joint thought. I say this for a couple reasons:
1: My TJ has 125k on it...about 45k of those miles were mine. I have not replaced the unit bearings yet, and I highly doubt someone else did. Mine are making a gritty noise, so they do need replaced, but my camber isn't jacked up because of it. 32k seems like an early life for wheel bearings unless you spend all your time playing in the mud.
2: When I replaced ball joints on my jeep, I had some slop and some bad tire wear patterns. They did not cause my my camber to be messed up though. However, when buying ball joints, they had the factory style (cannot adjust camber) or they had another style where you could adjust camber...theoretically, I would think that an extrememly bad ball joint would cause messed up camber.
It is very common that bad ball joints result in being able to move the wheel back and forth. 3JKs made a good comment on how to check this.
@derf...My understanding is that a TJ Rubicon D44 front axle is basically a Dana 30...except for the differential and the inner axle shafts. A JK Rubi 44 is much closer to being a true Dana 44. I also don't believe that you will go about bending and screwing up factory housings unless you are jumpin and bouncing the jeep. Granted I do not know how the OP drives offroad, I am not convinced that bent axles is a normal occurence.
|11-13-2012 01:15 PM|
I'm sticking to my ball joint opinion, unless you do some serious off roading or beat the crap out of your jeep your axels should hold up fine, keep in mind some people say a black eye is domestic abuse and others say its love. And I have no idea how you treat your jeep. If I were you I would have at least two mechanics look at it.
Keep us updated
|11-13-2012 10:02 AM|
The wheels wobbling back and forth a little also means that the unit bearings are wearing out. 35" tires off road will do that too. But new unit bearings alone might not get you back to looking like this: |------|
You really should put new unit bearings in, no question. But if you're still tilted you need to start making a plan to replace the front axle. Investing in a Dana 44 from someone like Dynatrac will, in the long run, save you money over swapping in even a Rubcon Dana 44. The Rubicon D44 is really a D44/D30 hybrid that has a lot of the weaknesses of the D30. An aftermarket D44 will be a lot stronger and will take the abuse of off roading a lot better than any factory axle.
|11-13-2012 09:32 AM|
|kik||Not only Jeeps. Any vehicle that I've seen with the wheels as you descibed needed ball joints.|
|11-13-2012 08:38 AM|
Both the unit bearing and balljoints start wearing the first day you drive the jeep. To see which ones need replacing (or both) jack up that side of the axle with wheel still on the jeep. To check the ball joints, slip a 2x4 under the tire and lift up, also leverage the tire back. You can also both pull and push the bottom and top. Have another person look at the ball joints for slop. If they are moving alot, have them replaced with the unit bearing.
The unit bearing will have it's own slop, up/down and side to side.
Cheaper to have them replaced at the same time that taking it apart twice.
Actually not a bad DIY project.
|11-13-2012 06:44 AM|
|Silverton34||I would think ball joints too. If the unit bearings were bad enough to let the tire visibly lean then they are worn completely through the needles and there would be significant noise. The balljoints would be pretty silent.|
|11-13-2012 06:15 AM|
|burton861||its got 32,000 miles on it. With 35 inch tires for all of those miles and it does go off road|
|11-13-2012 01:48 AM|
|11-12-2012 11:12 PM|
|11-12-2012 10:12 PM|
|burton861||Sooo.... Ball joint or new bearing hub assembly? Who thinks what?|
|11-12-2012 10:08 PM|
|Ruby Tuesday||I have never been into the front axel on my JK, I base my opinion on experience with solid axel Ford and Chevys. With that said I could be wrong|
|11-12-2012 10:03 PM|
|11-12-2012 10:02 PM|
|11-12-2012 09:59 PM|
|Ruby Tuesday||It just sounds more likely ball joints to me, if your wheel bearings were so wore out that you could see the tire sitting off camber the bearings would be gone and the tire wouldn't turn at all. However, wore out ball joints will do exactally what you discribe|
|11-12-2012 09:51 PM|
Raziel- How could you get them cheaper, and how much?
Ruby- I am not sure what it is so I am open for opinions. If you jack the car up and are looking at the tire like this- O -then you can push the top and bottom and it will move back and forth. This mechanic is not "out to get me" so a second opinion would only be for knowledge, if that is what you were referring to.
|11-12-2012 09:44 PM|
|Ruby Tuesday||Sure it's not your ball joints? You might want to have a seconed opinion|
|11-12-2012 09:26 PM|
|11-12-2012 09:23 PM|
|Raziel||Yea, I can't get it for much less than 130.00|
|11-12-2012 08:57 PM|
Let me see how much I could get them for you. I might be able to save you some money if you want? I'll post later.
|11-12-2012 07:56 PM|
|jtbaker1911||you need two hub bearings. One for each side. These are sealed for life bearings. You have to replace the hub assembly.|
|11-12-2012 07:20 PM|
|11-12-2012 05:57 PM|
|WatchThis!||Lol you better hope you don't have to replace the pinion bearing anytime soon. That would cost you way more then what your problem seams to be now.|
|This thread has more than 30 replies. Click here to review the whole thread.|