|03-23-2013 01:24 PM|
Too many choices!! LOL
For windshield mounted lights...what is best or most practical?
Wide, pencil or long range beam bulbs?
What wattage is best? 55, 100 or 130? overkill on 130?
I don't trail ride often and when I do, it is more stock type.
|03-20-2013 09:57 PM|
|Ebxgsxr||EMT jeep is right. they were the Black magic 1000's. my current TJ doesn't ahve lights that big, lol.|
|03-20-2013 08:47 PM|
|03-20-2013 08:37 PM|
|11-26-2012 04:30 PM|
I just put a set of KC brackets on this past weekend, and have a set of 6" Daylighters on the way now, but just bought some Pilot 6" which are identical (shape & size) to the daylighters, and when I test fit them, they looked perfect.
What has everyone done with their antenna though? Only one day driving with these brackets and I'm already batty from hearing the antenna 'tink' against the bracket every 1.2 seconds.
|11-18-2012 10:36 AM|
|Sheweezy||Thanks for the wiring ideas, I'll have to try em out|
|11-18-2012 02:08 AM|
|duaneduanet||I had a YJ and was going to install windshield light brackets on it, but luckily a friend of mine did it first and found that the nuts on the back side of the windshield weren't welded to the windshield frame. Is my TJ the same? Or is the frame actually threaded?|
|11-17-2012 12:53 PM|
that's what i'm running on my current 99
as for running the wiring, i didn't want to drill any holes. i don't have any current pictures, but on my old 2001 i ran them through one of the bolt holes of the windshield light bracket. remove the bolt & it's a straight shot into the interior of the jeep.
before i had cleaned it up.
|11-17-2012 11:03 AM|
|kpla51||i have smitty built brackets with kc day lighters and they fit fine|
|11-17-2012 08:47 AM|
(It may seem lazy but) My wires run through the door openings - I have little slide on connectors just inside the doors.
I wanted to make it very easy to disonnect the lights if I needed to in a hurry - which has been very useful when I accidently busted the lights off in seperate incidents.
|11-17-2012 08:37 AM|
|11-17-2012 08:22 AM|
The pic on their website is of a JK (I think).
|11-17-2012 08:15 AM|
|Sheweezy||Not as much a mounting question here, but where do you guys run your wires to hide em? Not many options out there|
|11-17-2012 08:01 AM|
|Chadd388||The PIAAs mount under the hinge like that.|
|11-16-2012 06:29 PM|
I used to have Rugged Ridge brackets and they fitted fine - the holes for the lights are slotted so you can slide the light back and forth if needed. Just position the lights so you can still lean the hood back on the windshield when you want to.
I'm now running Warrior Products brackets - they bolt up under the hinge and are a lot lower which is good for visibility - if you have a ragtop fitted, the A pillar creates enough of a blindspot as it is.
The Warrior Products brackets also sit the lights out a little bit wider - I think this is for clearance if you want to rest the hood on the windshield. But being out a little bit wider means they will also cop more trail damage (it's kinda a trade off) so the covers are always on if I'm not using the lights.
I've busted the lights off on both sides laying the Jeep into dirt walls but everything was easily repairable.
'Pencil beam' lights are best for the windshield hinges.
Some guys have mentioned glare off the hood - that may depend on the color of your Jeep. Mine is dark green and I've never noticed any glare. But it would depend on the type of lights too - I wouldn't run LEDs or wide beam lights on the windshield hinges for example.
Whatever you get will most likely interfere with the radio aerial so be prepared to take that off or bend it out of the way.
Here's a pic of the Warrior Products bracket bolted under the hinge - you can also (just) see the KC locknut I put on the light to deter theft.
|11-16-2012 05:00 PM|
KC Bracket and Lights
KC Windshield Light Brackets and Apollo Long Range Lights.
|11-16-2012 01:26 PM|
|Chadd388||I'm running the PIAA 5400 kit.|
|11-16-2012 11:46 AM|
|Moose5||I got the PIAA mounting brackets and installed the KC Daylighters. Now, the Daylighters are a solid 5 inches deep and about 6 inches wide, and there is no interference with the windshield at all. The good thing about the PIAA brackets is they re offset to the side a bit, if that helps at all|
|11-16-2012 11:39 AM|
|luckyluke13||Kc brackets - kc 6" lights, perfect fit!|
|11-16-2012 10:32 AM|
KC brackets and Hella 500's for me.
|11-16-2012 10:23 AM|
|free78||Looking at the KC light mounting brackets. I have read I believe rugged ridge brackets don't always line up with bolt holes.|
|11-16-2012 09:56 AM|
|erickpl||I have the KC light mount, but run IPF 968's.|
|11-16-2012 09:49 AM|
|Neil F.||Let's start with what brackets are you looking at ordering first.|
|11-16-2012 09:34 AM|
I used cheap 6" slim lights from Northern Tool.
|11-16-2012 09:18 AM|
Windshield Light Mounting Braket
Did a quick search and found a few threads but......... What light are you running on your brakets? What size light will fit on the bracket depth wise? I dont want to order brackets and lights and the lights hit the winshield and not mount for being to big.