Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > 95 YJ on Tons

Join Wrangler Forum Today


Thread: 95 YJ on Tons Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-30-2012 10:15 PM
Rusty Knutt Hey my elderly neighbor just wrecked his 79 cheby. Hows the front clip? That is if you haven't scrapped it.
12-15-2012 07:22 AM
06blackmax I've decided to run my shocks outboard on all four corners so a little time with a tubing bender is in my future.
12-15-2012 07:15 AM
06blackmax We have a roller!



More to come.
12-15-2012 07:11 AM
06blackmax Couple more of frame. Rear.


Another of front.
12-15-2012 07:07 AM
Irongrave thats fine to do it one a budget but spend a little time building something that might actually work on the trails. I would personally trash the stock shackle mounts, french the frame mounts and run XJ leaf springs to get some much needed added wheel base
12-15-2012 07:05 AM
06blackmax Worked on my frame last weekend. Went from this.


To this.


And had this left over.


A few more minor things to clean up and paint it and reassemble.
12-15-2012 07:03 AM
06blackmax
Quote:
Originally Posted by Irongrave View Post
why use stock springs in the stock location if your putting it on full width axles?
Biggest reason is I can't afford to do arms and coil overs. This is a budget build to get it going I can redo later as time and money allows.
12-15-2012 07:00 AM
06blackmax
Quote:
Originally Posted by denisbaldwin View Post
You plan on shaving that 14 bolt? what tire are you going to run when it's done?
It's not in the budget right now but probably. Tires will probably be in the 38" range.
12-10-2012 03:19 PM
Irongrave why use stock springs in the stock location if your putting it on full width axles?
12-10-2012 12:59 PM
denisbaldwin You plan on shaving that 14 bolt? what tire are you going to run when it's done?
12-02-2012 08:58 AM
06blackmax Carried the tub and frame to my shop over the long weekend last week. This weekend will try to get started on getting the tub off the frame and putting some springs back under it.


I made a little progress this afternoon. Started with this.


You just gotta love having a forklift.


Got down to this.


Got it in the shop and started putting some stock springs in it to get measurements for when the axles go under it. Next on the motor install.
11-20-2012 06:36 AM
06blackmax I will keep the 203 for a hopeful doubler upgrade in the future, but am looking for a 205 with a fixed rear yoke. If I can't find one by the time I get it done I'll use the 203.
11-19-2012 08:55 AM
Ibuildembig Are you going to keep the 203?
11-19-2012 06:52 AM
06blackmax Well I took big red to my shop this weekend and pulled the engine and trans/t-case. This week I'll pull the axles and start cleaning things up and replace gasket as needed. Maybe over the long weekend coming up I can get something done.





11-04-2012 08:37 AM
06blackmax Drove the donor truck around yesterday for a couple hours. It holds 45psi oil pressure at 180* and runs great. I think it's going to be a great setup. Now to get it in the Jeep and on a trail.

PS, anybody want to buy a 79 Chevy truck body?
11-01-2012 08:02 PM
06blackmax
Quote:
Originally Posted by Ibuildembig View Post
Ya found a K30 with a 10 bolt? Someone already rob the nuts out of it?
I'm guessing it went on to bigger and better things. That's why I asked about a D60 the other day. I can use this one to mock up and find one along the way.
11-01-2012 04:55 PM
dezertrat84 Sound like a bad ass build...
11-01-2012 03:23 PM
Ibuildembig Ya found a K30 with a 10 bolt? Someone already rob the nuts out of it?
11-01-2012 12:23 PM
06blackmax It'll be a little work. But it'll be fun.

Motor runs great and trans and T-case work fine. So mounts and wiring to get going and take all apart for cleaning and paint. Hoping to have the bulk of it done around New Years. MSJ is having a New Years ride at Superlift, so well see.
11-01-2012 09:06 AM
nick50471 Looks like work.
11-01-2012 07:18 AM
06blackmax
95 YJ on Tons

The time is here. My project of choice is a 95 YJ that has been stripped of its drivetrain. So I have a clean slate so to speak. Over the last month or so the project changed somewhat but here is where I stand.

95 YJ
350
T-400
203
14 bolt rear
Corp 10 bolt (8 lug to match) up front

What I'm starting with.



The donor truck I found for the drivetrain is a 79 Chevy K30. It's got a mildly built 350 on it with the 400/203 and axles. As it sits now.



Unloaded it and it it running. Had to adjust the valves cause it sounded like a typewriter. Then after fixing a hose on the modulator valve the trans shifts smooth and crisp. I think it will all work out.

Over the next couple weeks ill be pulling the motor and drivetrain and replacing any gaskets and misc. items for preventative maintance. And then start with the fabing and wiring of the beast. I will try to find a D60 front when I get closer to being done but for now the 10 bolt will work for mock up.
Thanks for looking, let me know what you think.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:06 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC