|12-07-2012 10:12 PM|
|jrussblues||I swear I only took it out to be measured for shocks and to have a windshield installed. Oh well, I'll clean it up tomorrow. Also, a 360 and glass packs are a nasty combination. It looks like I'll be changing the exhaust to stay under the radar.|
|12-05-2012 09:31 PM|
Getting close, new front winch bumper courtesy of searchers 4wd, mirrors are on, dash is wired and wires are tucked, and I finally got around to putting on my rear wheel spacers.
Tomorrow I go get my license plate and install my windshield, horn button, horn button and plastic gas cap housing thingy. Then its off for its maiden voyage to the 4wd shop where I can fit it for shocks and re-weld my rear shackle hangers. Wish me luck. Should be ready by the weekend.
|12-03-2012 02:36 PM|
|jakekaminski||wish i would have had time to fix mine up.|
|11-20-2012 10:12 AM|
|11-20-2012 10:10 AM|
At full choke the way I got it. We've come a long way and still have a little ways to go. And yes, the 360 is still lime green, not my choice but I wasn't going to get into taking it down and repainting.
|11-20-2012 10:07 AM|
The motor craft 2100 2bbl
...or as I like to call it now, the ak47 of carbs.
As I said before the p.o. destroyed this cj. The 2100 has survived the blast. The choke pull off was broken, the thermostatic choke was not adjusted, the butterfly linkage was not adjusted and the Carb wouldn't choke. All of that and the thing would still run?
This is literally the 1st Carb I have ever worked on and it was super easy. I am still working out the kinks in timing and idle but it has only 3 adjustment screws and an adjustable thermostat. I may end up rebuilding it but for right now I am afraid it would do more harm than good.
|11-20-2012 09:51 AM|
I changed the input shaft seal and the boot on the gear box/lower steering shaft.
I upgraded the gear box mount with a rugged ridge HD mount.
I also upgraded to searchers steering linkage.
You can see the difference in size alone with the factory rod end. The factory tie rod was bent due to the 38's that the p.o. installed and as a side note, it makes a really nice hood prop.
I have been astonished at the durability of the factory parts. The pump had not been hooked up in years, I attached a belt, added fluid and bled...it works like a champ.
As another note, the HD steering mount actually pushed the PS hoses up which interfered with the radiator. Just had to carefully bend them down a little.
|11-20-2012 09:39 AM|
Mating the 435
The transmission to bell housing was easy. And advance adapters made it even easier with great instructions on changing the output shaft.
Mating the Dana 20 to the 435 became more challenging.
The shaft that holds the shift linkage was way to long and wide. The solution ended up being to shave some of the cast iron off, shorten the shaft and install a jb twin stick. After extensive conversation and stumping the guys at advance adapters I came to figure out that this was due to the Dana 20 set up only with the t150. Other Dana 20's are apparently more agreeable with the swap.
|11-20-2012 09:17 AM|
First pic is the antifreeze that came out...score that there was no coolant in the oil.
2nd pic...the rear brakes...roasted.
I had a pic of all of the crud that came off of the frame but I can't find it. There was mud in every imaginable crevice.
|11-20-2012 09:14 AM|
|jrussblues||Necessity is the mother of invention. Here I can be seen using a cork screw to remove the retaining ring from the steering shaft to change the turn signal and ignition switches.|
|11-20-2012 09:05 AM|
|jrussblues||When removing surface rust on a frame with an angle grinder goes bad. Lesson learned...wear jeans.|
|11-20-2012 09:03 AM|
|jrussblues||Just realized that in all of my business I left out a lot of pics and info on the rebuild. So I'll start posting those with some info throughout the day.|
|11-19-2012 11:17 AM|
Then and now.
Replacement tub was in worse shape than I expected so looks like full corners and sliders will be in line. Other than that its down to a windshield, shocks, mirrors and reverse lights.
|11-10-2012 03:33 PM|
Been a while since I posted but here are a couple of pics.
Dash is in and we are about 95% wired. I still have to route and wire back up lights and the oil pressure/temp gauges when they come in. I also bedlined the tub and fabbed a swing open tire carrier. The 35 fits perfectly back there. All that's left to do now is put on the rear spacers, put in seat belts, put on the windshield and wire the wiper motor, get the windshield glass installed, put on jeep logo stickers and go thoroughly fail a state inspection.
|10-22-2012 02:01 PM|
|jrussblues||Well it runs somewhat reliably now, and I fabbed a front bumper out of a yj bumper. Fun fun. And, of course the mobile ap won't let me post a pic.|
|10-06-2012 08:35 PM|
|jrussblues||Progress...still a ways to go though|
|09-28-2012 11:25 AM|
|jrussblues||Wiring stuff sucks|
|09-23-2012 10:00 PM|
|09-21-2012 05:31 PM|
|09-10-2012 10:49 PM|
|09-10-2012 10:37 PM|
|tomthbomb||The roll bar on a 78 was vertical not slanted back. I think the slanted roll bar started in 1979 or 1980.|
|09-10-2012 10:31 PM|
|09-10-2012 10:25 PM|
I see you went with a later model tub with the "slanted" roll bar. I did the same except I kept my vertical roll bar to accommodate the CJ-8 half top.
Will be watching your project. Good luck.
|09-10-2012 07:36 PM|
|jrussblues||Tub is on...woo hoo|
|08-23-2012 09:00 PM|
Stupid phone won't upload pics but here's where we stand.
4.5 re lift
1 piece g2's
New rear brakes
New e brake line
Rr HD steering box mount
New steering box input seals
Replaced turn signal switch and ignition switch
Repainted roll bar
Painted and reinstalled exhaust
New genright rear cross member
I have my knuckle over steering being fabbed and I've already got a pair of corbeau seats and a 12 fuse wiring harness to go in.
From here I'll get the steering done, install the twin stick and shim the rear axle then the tub goes back on and the real fun begins.
This has been a blast and a much larger project than I originally anticipated.
|08-15-2012 12:24 PM|
|08-14-2012 08:57 PM|
|08-14-2012 08:20 PM|
|jrussblues||Narrow track axles/shock mounts and I just pulled out a t150. If its not a 78 its pretty close.|
|08-14-2012 07:34 PM|
|08-14-2012 04:51 PM|
|This thread has more than 30 replies. Click here to review the whole thread.|