|01-02-2009 02:23 AM|
Here's the strengthening of the pod.
Total weight added about 3 lbs.
|01-02-2009 02:09 AM|
When I first got my Rubi I tried a Kilby steering box plate. It only protected about 1/2 the steering box, leaving the inside half open and unprotected. I wondered what trails have only 1/2 rocks that might do damage.
I returned it and made my own.
They may have improved them since.
While you are putting on a steering box skidplate, why not enhance the mounting for the box at the same time. The steering box mounts to a "pod-like-protrusion" under the frame. That "pod" has a tendancy to break off, or at least snap the welds, leaving you without steering. A skid plate helps, but doesn't prevent it from breaking.
Add a full plate along the outside and weld it to both the frame and pod. Add gussets to the front, rear, and underneath the pod to.
The cross brace from the box to the other side frame rail also helps, but the Ruby boxes are shaped different, cross braces don't work on them.
It's not a fun feeling when you realize you can't steer it.
|01-01-2009 11:34 PM|
|flattietj||i like kilbys products.....my fuel cell is now in the back of the jeep but before, the skidplate held up well.......my stock skid also held up well......it had a 5 inch radius but it was still in tact|
|01-01-2009 09:59 PM|
|Never Monday||I think Rokmen found a good marketing angle. I like the flat surface to slide off of.|
|01-01-2009 09:57 PM|
|Triple88a||alright nico i guess u have ur answers man. Order it now, when u get it by next Christmas, put some rubber on the sides of it to form the "dimple" from the inside and go try it out|
|01-01-2009 09:57 PM|
|4.0l sahara||Well i have a EMP skid it has no dimple and i've had no probs and it is strong.|
|01-01-2009 09:55 PM|
|distortedtj||It doesn't cause problems for those that run the Kilby skid. Some do put rubber on the sides of the tank to space it. Both ways do not effect any of the jeeps opperation or harm it. From experiance. Not reading it.|
|01-01-2009 09:53 PM|
|Triple88a||i'm not questioning the strength of it.|
|01-01-2009 09:44 PM|
my gas tank skid doesnt have that dimple either
but I took some rubber matting from home depot and lined the bottom of the skid plate leaving a hole in the middle for the tank dimple to sit in
I have the kilby steering box skid and have hit it on rocks it seems to hold up just fine
I have come down hard a few times on my gas tank skid and it hasnt even dented just scratched it
|01-01-2009 09:35 PM|
|Never Monday||I'm not asking. i'm telling you I haven't seen it as a problem.|
|01-01-2009 09:34 PM|
YouTube - ROKMEN Jeep Wrangler Gas Tank Skid Plate Tech Overview
|01-01-2009 09:31 PM|
|Never Monday||but on the 97-02 the Kilby also raises the tank an inch|
|01-01-2009 09:30 PM|
|distortedtj||tripple, the rockman tank works with a body lift to also raise the tank up. Reason for the needed dimple with theirs.|
|01-01-2009 09:28 PM|
|01-01-2009 09:24 PM|
|01-01-2009 09:17 PM|
|Never Monday||not needed. This think is a tank. Everything in the picture is surface scratches, not one deformity in the skid.|
|01-01-2009 09:15 PM|
|Triple88a||wow do they have a dimple in the middle? it doesnt seem like it.|
|01-01-2009 08:42 PM|
I think so
|01-01-2009 08:17 PM|
Are the Kilby skids worth the money?
I want to buy a stering box and gas tank skid in the next weeks.