Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Viper security/power locks

Join Wrangler Forum Today


Thread: Viper security/power locks Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-18-2012 06:31 AM
LilYeller when you install that security system you will be splicing into power at your main harness near the steering wheel. Grab the power from there also. I use www.the12volt.com for wire colors and they have great writeups for people who arent that experienced with alarm system installs. The TJ is very easy to work on, the alarm is one of the easier pieces of electronics to add. Proper prep is the key. bench prep the alarm before the install, this means roll up all the wires that you arent using before you start connecting the alarm to your Jeep. When you get your alarm you will see loads of wires, you can reduce this to about 8-10 wires cause most of the wires arent needed for a TJ install. This will keep the work area nice and clean and way less confusing. If you want more help after you get the alarm just post up here.
12-18-2012 12:56 AM
coastalwrangler Ok I've just decided on getting the viper keyless entry system with built in relays and tying the door lock actuators into that. I just have one more question about where I can get the power for it though. Would it be possible to splice it off of the 12v power outlet that's next to the cigarette lighter?
12-12-2012 10:41 PM
coastalwrangler
Quote:
Originally Posted by doclouie View Post
I actually just got done reading your write up doc. That's how I planned on installing the actuators. Did you just order the remote entry kit without the alarm from that site? I was looking at the avital security and remote entry kit that they have for around $150, but Amazon sells the Viper 350 systems for around $50 and I was wondering how hard/expensive it would be to tie outside actuators into this system. Thank you for the replies.
12-12-2012 10:37 PM
doclouie Take a look at this.

http://www.wranglerforum.com/f5/power-locks-50781.html
12-12-2012 08:58 PM
coastalwrangler Sorry, yes I do have full doors. I've seen actuators that will fit inside of the door panels. I'm planning on just drilling a hole and using a rubber grommet to run the wire through, then just using some disconnects to avoid having to cut into the frame to add contacts.
12-12-2012 08:36 PM
Slater451 Well first you would have to be sure all that stuff would fit inside the doors. Assuming you have full doors... Also how are you going to get the power there? Are you going to have a permanent wire feeding the switches and actuators or jam tacs so you can remove the doors with out any electrical connections .
12-12-2012 08:30 PM
coastalwrangler
Viper security/power locks

Hey folks. I've had my TJ for a while, but I'm new to the online community. I currently live in a somewhat shady area, so I'm thinking about asking for a Viper 350 plus security system for Christmas. While I'm messing around with it I was also thinking about the power lock upgrade since the expandability is there. I have the DIY mindset and I've done all of the audio upgrades myself, so would it be relatively easy to figure out how to tie the locks into the security system? Also, I know I'll need to pick up the actuators separately from the security system, but would I need anything else for this project?

Thanks for reading and happy holidays!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:35 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC