Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > oil pressure sender

Join Wrangler Forum Today

Thread: oil pressure sender Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-19-2009 08:38 PM
whitebuffalo make DAMN sure you put even pressure in the right direction on it......if it breaks, its a mofo. (mine had been jerry rigged by PO and when i went to remove it, it snapped off even with the block....and easy outs dont work on brass)
01-18-2009 11:59 PM
speepdaedeesi ok found it easily, but i dont have any wrenches that big. i do have a socket but its not deep enough.

should have it done tomorrow. the guy im swapping tops with is a 18wheeler mechanic so im sure he might lend me something a little deeper
01-18-2009 11:12 PM
speepdaedeesi lmfao gorillafistisatorquespec

ima go try it in a sec.. wife wanted to watch saw 5

it was pretty good
01-18-2009 08:27 PM

4cyl tj should be similar to the 4.0's i seem to do a ton of. it should be by the filter, accesible from up top.
01-18-2009 07:57 PM
speepdaedeesi gorilla in a jeep commercial

YouTube - Funny gorilla
01-18-2009 07:55 PM
speepdaedeesi diggin the new avatar.

one last question. probably the most important in relation to the swap.

where is it located lol. ive read its near the oil filter.. i have a 2.5

whats the best approach angle to get it out? above or below the jeep?

and where is it in relation to the filter?

just trying to make things smooth.. wouldnt want to throw a ''monkey'' wrench in the gears
01-18-2009 07:48 PM
speepdaedeesi cool. im gonna tackle it tonight.
01-18-2009 07:29 PM
jpdocdave great pic, i think i got a new avatar for the first time. wrench will work to, as long as there's room to turn it. and yes a socket would have to be deep.

some oil will usually leak out, but just a little, but a drain pan under it and you'll be fine.
01-18-2009 07:24 PM
speepdaedeesi lol @ gorilla fist

01-18-2009 07:23 PM
speepdaedeesi roger that. i was going to match the new one up with a nice closed end wrench as it would have to be a super deep socket to get it on/off.

is oil going to pour out?
01-18-2009 07:19 PM
jpdocdave super simple, but make sure you have a socket that will fit it. just turn the old one out, and put the new one in. do not gorilla fist it, just has to be snug.
01-18-2009 07:15 PM
oil pressure sender

got a new one tonight.

anyone want to write me a quick how to for the swap out?

its cold as all get out in the garage and i dont want any suprises. dont want to be out there any longer than i need to


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:55 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC