Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 2004 5.3 vortec/swap

Join Wrangler Forum Today


Thread: 2004 5.3 vortec/swap Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-20-2012 11:44 PM
Baja1ab 101 pages to read here..... Have fun.

5.3 Jeeps - Pirate4x4.Com : 4x4 and Off-Road Forum
12-20-2012 10:15 PM
Ballesterosrg
Quote:
Originally Posted by redneck1984
You did the 5.3? If so minus the engine and tranny, how much was the rest of the needed parts, and roughly how long did it take?
You need a transmission to t-case,I got it From advance adapters also the motor mounts. I did the sleep yoke eliminator at the same time, also from advance adapters. When I got my engine and tranny it came with the wiring harness and computer so i sent it to Novak adapters and they fixed it to fit my yj. I only had to connect 7 wires. I got a shifter from advance adapters for the 4l60 e. also a radiator, an electric motor fan, but you can use the one that comes with the motor, an air filter and a few elbows for the air filter, I got the gas lines and fittings from speedway motors, I had to replace all the gauges in dash board, and send it to a friend to do a custom made muffler with a flow master, then a year later I broke my Dana 35 so I replaced it with a ford 8.8, but I knew this would happen so I was saving for it. It took me about 3 months to finish it by my self, but I would have done in less time if I didn't run out of money. I don't regret doing this because I had a lot of fun during the process. And the satisfaction with the results is priceless.
12-20-2012 08:01 AM
redneck1984 You did the 5.3? If so minus the engine and tranny, how much was the rest of the needed parts, and roughly how long did it take?
12-20-2012 12:21 AM
Ballesterosrg
Quote:
Originally Posted by redneck1984
I have an opportunity to swap to a 5.3 vortec-4l60e tranny and t case (not sure which one it is but i think should be pretty good) the donor vehicle is a 2004 avalanche.
My jeep don't need this big of an upgrade, but my families goal for our jeep is bigger axles and lockers with 37s...
So i guess my question is, would a 4.0 be ok or should i do the v8 swap while i have a chance to get the 5.3 for really cheap?
And if swapping to the 5.3, how difficult is it, or what would a shop charge to do something like that (ballpark). Any information on this will be very grateful, thanks.
If you have the time and money go for it I did the same swap to mine and I've never been happier with my jeep I got a whole lot more power and way better mpg.
12-17-2012 06:23 AM
denisbaldwin The 4.0, especially if geared right, should do fine for most of what you'll need, even up to a 37" tire.

That said, there's no replacement for displacement and if you can get the 5.3 cheap, I say go for it.

You'll need adapters (most likely that tranny to the t-case you already have) from novak:
Adapting the 4L60E Transmission to the Jeep NP / NVG Transfer Cases

You'll also need the computer connector from Howell (or similar) for the harness.

Then you'll need cooling, motor mounts, etc.etc. It's a big project but it's been done thousands of times and is well documented, so shouldn't be an issue.
12-16-2012 08:29 PM
redneck1984
2004 5.3 vortec/swap

I have an opportunity to swap to a 5.3 vortec-4l60e tranny and t case (not sure which one it is but i think should be pretty good) the donor vehicle is a 2004 avalanche.
My jeep don't need this big of an upgrade, but my families goal for our jeep is bigger axles and lockers with 37s...
So i guess my question is, would a 4.0 be ok or should i do the v8 swap while i have a chance to get the 5.3 for really cheap?
And if swapping to the 5.3, how difficult is it, or what would a shop charge to do something like that (ballpark). Any information on this will be very grateful, thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:08 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC