Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > Carbed 4.0L

Join Wrangler Forum Today


Thread: Carbed 4.0L Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-14-2012 07:18 AM
busemans yes but the dude who started the thread back was asking the same thing
04-14-2012 06:57 AM
Coyote_94YJ You guys realize this thread is 3 years old, right?
04-10-2012 04:06 PM
busemans they did but they are computer controlled, completely.

its a huge step down to go carb'd on a 4.0.

but, you can. get an offenhauser intake and a 1.23 or 1.14 mc2100/2150 carb and it will run fine. a buddy did his 93 yj last year.

the 4.2 head will bolt to the 4.0 but the copmression will be very low
04-10-2012 02:00 PM
Xpress I would also imagine that in order to convert the 4.0 to a 4.2L intake (a very morally unjust action- just buy a damn 4.2 and give the 4.0 to someone who wants/needs it) you are going to have to tear out a lot of sensors that have a part in controlling the ignition systems- basically you're looking at messing with a lot of the wiring harness just to get your carb'd 4.0 to run properly seeing as how the ignition system is completely computer controlled and relies on those sensors.

Did the YJ 4.0's come with a distributor setup? I know the TJ's switched to a direct igniter setup over the older distributor setup, which means that it's basically not possible..
04-10-2012 05:31 AM
spunebil I saw plenty of hills over there
Espesialy in scotland where I lived for a year and half.
But also saw them in england and all over wales!
I am in missouri now but have to travel 120 miles to nearest offroad park and most of the better ones are 150 to 250 miles!
04-10-2012 03:56 AM
TomTankslely It sounds to me that you want a mechanical carb.
04-10-2012 01:23 AM
Xpress WHY would he want to do that? There goes EVERYTHING that makes the 4.0L the desired engine with power output and reliability. It's incredibly stupid. Every bit of good MPG it has is going out the window.
04-09-2012 11:08 PM
BDK
Quote:
Originally Posted by 93 SAHARA View Post
I'm also interested in getting rid of my Electronic crap and Computer? I'm looking for information to swap 4.2 Carburetor and Intake Manifold on a 4.0 ? if it's possible can I disconnect the computer ?
You would have to swap out your intake to a older CJ/YJ one. Do not use the Carter carb, its garbage! Look for a MC2100/2150. Bolts on with a Rochester adapter plate. Or find a 4Bbl intake and go for a Holly truck avenger.
04-09-2012 10:52 PM
khende The 4.2 carb is run by a computer and it a piece of crap. It sounds to me that you want a mechanical carb. I have not researched this but there has to be a better solution than the 4.2 carb. I think that you are barking up the wrong tree.
04-09-2012 09:03 PM
93 SAHARA I'm also interested in getting rid of my Electronic crap and Computer? I'm looking for information to swap 4.2 Carburetor and Intake Manifold on a 4.0 ? if it's possible can I disconnect the computer ?
01-23-2009 07:24 PM
jpdocdave well i'll go dig one out of a bone yard for a few hundred bux, give me a grand and sell it to him
01-23-2009 07:17 PM
Coyote_94YJ Hills in England........Where? Please tell me so I can go play on it. I doubt this jeep will see much trail and V-8's are a bit more rare over here. I could sell my 350 for £2000 easy over here.

I'll let him know about the head swap option.
01-23-2009 07:05 PM
jpdocdave i understand that part, but then just go carbed old school v8 then. but the stupid thing is a carbed v8 in normal form puts out what, 150-175 hp usually. the old 304 v8 was even less. and carbing the 4.0 is just a weird idea. who makes a carb to do it? i know you can put a 4.0 head on a 4.2 to gain the fuel injection, maybe he'd have to swap the 4.2 head on the 4.0 block.

the one i'm building will be very mechanical, but i'm not giving up the fuel injection. oh yeah, carbs are not very good on trails w/ steep angles.
01-23-2009 06:33 PM
Coyote_94YJ The guy wants to ditch the electronics and go all mechanical.
01-23-2009 05:39 PM
jpdocdave man thats dumb. i wonder if a 4.2 intake manifold would bolt onto a 4.0 head. why not put in a 4 cyl to.
01-23-2009 05:02 PM
Coyote_94YJ
Carbed 4.0L

I have a friend over here that has a 4.0L and he would like to remove the fuel injection and put on the fuel and ignition systems from a 4.2L. I've tried to talk him out of it but it ain't happenin. I have to ask you all because I've never had or worked on a 4.2L and my jeep didn't have a 4.0L in it for very long so I don't know much about them either. So...

Is it possible to take the 4.2L fuel system and ignition system and bolt up to a 4.0L?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:30 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC