Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Rear upper shock mount

Join Wrangler Forum Today

Thread: Rear upper shock mount Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-26-2012 11:58 PM
The Yetti Gonna try and put the lift on tomorrow so I will check then and get back go you. Thanks for all the help
12-26-2012 12:56 PM
89quest You shouldn't have to replace the mounts if they are indeed stock, something is amiss and you will find it, keep looking.Can you get in there to take a measurment, I know its tight.It might give some insight as to what is going on.
12-26-2012 02:48 AM
The Yetti No these would be the first set of non stock shocks. Do I really need to replace the entire mount? The new shocks aren't a drastic change from the stock shocks
12-25-2012 07:57 PM
89quest Just a shot in the dark, have your shock mounts been changed from stock? While under mine recently both my shock mounts had been replaced and reenforced by someone along the way
12-24-2012 10:36 PM
The Yetti No, I have the thick white shock part at the bottom.
12-24-2012 10:17 PM
cRaZy888 Its not upside down is it?
I thought I remember the tops and bottoms being different sizes?
12-24-2012 10:04 PM
jokerchief462 I know what u mean. I have done it only to get a dd back on the road.
12-24-2012 09:51 PM
The Yetti Yeah they're good, I'm not sure how to change the bushings though... Yeah thought about drilling it out. Didn't want to risk the slaughter to the bushing if the drill caught the rubber good
12-24-2012 09:28 PM
jokerchief462 Are the old rubber bushings any good??? Reuse. Or I have done this drilled the rubber to the right size and it wasn't easy but it works.
12-24-2012 08:19 PM
The Yetti I know what you mean on the RE. There's not a clearance issue with the shock. And yes they sent the right ones the order and part numbers match up. I will try to get some pictures up but I guess my question is, is there anyway to temporarily expand the hole making it fit. Maybe heat it up? I'm sliding on the top first by the way. I've also tried bolting up the lower mount first and then sliding the top on
12-24-2012 08:09 PM
whiteyj Pics will help solve these kinds if issues much faster! What you are describing could be crystal clear to you but not so much for the rest of us. For example, on the RE kit my shocks had to be installed upside down to clear interferences.
12-24-2012 08:00 PM
Carralo1 Are you sliding it on upper mount first? Are you installing them so they expand up or down? They could of sent wrong ones.
12-24-2012 07:42 PM
The Yetti Everything is clear and where it needs to be just wont fit, even after being lubed up. Maybe I am doing something wrong? I'll check but I'm pretty sure everything was clear
12-24-2012 07:41 PM
The Yetti The mount is clean and the bushing is rubber with nothing inside of it. But it's smaller than the factory one
12-24-2012 07:04 PM
jokerchief462 Is the mount clean clear of the last hardware like is there a metal sleeve on there from previous shock?? Or is there a sleeve in the new one that needs to be removed?
12-24-2012 04:56 PM
The Yetti
Rear upper shock mount

I was installing my new shocks from RC with my 2.5 inch lift (did not replace springs yet). Got through the front shocks fine but I could not get the rear shocks to slide into the upper mount. Tried PB blaster, hammering, everything. Any suggestions on what I should do? Also, does it matter that I didn't tighten lower bolts to 45 ft pounds? I just tightened until tight.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:21 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC