Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > 07 power stearing issues

Join Wrangler Forum Today


Thread: 07 power stearing issues Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-31-2012 12:07 PM
nwbronco Simple enough. You will need a clam shell type pulley puller. Do not use a fork type. The core is metal but the majority of it is plastic. Remove the lines from the pump, cover the lines with a platic bag and duct tape. This will keep yo grom losing all the fluid. Take the old pump off. Use the puller to pull the pulley. Use it again to install the pulley on the new pump. Install new pump. Re-connect lines. Top off start engine. Note level of fluid. Turn wheels from lock to lock a few times. Top off again if needed. Check system again after a few days to see if fluid level is satisfactory.

Bob K.
12-30-2012 08:35 AM
dltucker77 Thanks for the info. I am going to check on a rebuilt pump tomorrow. How hard are they to replace yourself?
12-28-2012 02:47 PM
3JKs1H1 degrease the area and lightly hose it off. The pump/steerign gear box, and anywhere the lines run. Air bubbles indicate a leak from somewhere, so you should see it on clean surfaces. It could be a loose hose, missing o-ring on a line, etc. If you cannot repair it yourself, I'd go somewhere else. If he isn't warranting his work (free) -he is either using bad parts or isn't very good at his job.

Power steering pumps require bleeding before you start the engine (same with replacing the steering box). If that pump runs dry for just a bit, it'll get ruined.
12-28-2012 02:37 PM
dltucker77 I had a guy that worked on it. Not sure where he was getting the parts or what brand it was. Yes there are bubbles in the reservoir. I wouldnt even know where to begin on replacing one or installing an inline filter. I just keep filling it up and rolling on.
12-27-2012 10:29 PM
ESP Are you replacing each time with OEM? Who is doing the work?
12-27-2012 10:14 PM
3JKs1H1
Quote:
Originally Posted by nwbronco View Post
Where are you getting them from?
What he said. Got bubbles in the resovoir? I assume it's leaking out the shaft behind the pulley? Flush the system and bleed it. PS pump should last 100K miles. They make inline filters but that shouldn't be necessary.
12-27-2012 09:00 PM
nwbronco Where are you getting them from?
12-27-2012 07:43 PM
dltucker77 Thanks. Like I said, I am fixing to have to put # 4 on.
12-24-2012 03:24 PM
nwbronco I had the original fail. Got a re-built from NAPA. Holding up fine.

Bob K.
12-24-2012 12:46 PM
dltucker77
07 power stearing issues

I have gone through two PS pumps. Seems like my third is playing out. I constantly have to put fluid in it because it leaks down. Anyone else having or had issues? Any solutions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:00 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC