Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Saving my clutch

Join Wrangler Forum Today


Thread: Saving my clutch Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-29-2012 08:06 PM
Wattapunk I just spent $740 for a Luk clutch kit including installation at a local shop so your quote is about right if it's for the whole kit.
12-29-2012 03:55 PM
Sherpa Last fall my clutch throwout bearing disintegrated while I was on my way to run the Rubicon Trail. I limped to Elko, NV and had an independent shop replace it for me. It ran $800 total, including the new clutch kit, a new flywheel, a new slave cylinder (which he suggested on general principle) and labor. What I learned from this:

#1: do NOT have the flywheel turned! This tech would have turned mine, but I ended up having him install a new one just to save time (he would have needed to farm it out). After returning home, I learned that Jeep specifically says the flywheel has a special conical finish which should not be turned--only clean it off with emery cloth if it needs it.

#2: bleeding the clutch lines is a royal pain in the butt to do properly. These guys tried (since they replaced the slave cylinder) but failed, and I didn't know it until I began to drive home--air in the system soon rendered my clutch pedal completely useless, and I had to drive 250 miles home shifting clutchlessly (which is no fun in the mountains of I-80). Because of this, do NOT let your mechanic talk you into breaking the seal of your hydraulic system unless you have a component which has actually failed.

#3: inspect the entire Jeep carefully before leaving the shop--this includes crawling under your Jeep and checking that the trans mount's four nuts are properly reattached. My guy's air tool broke off two of the mount studs (which is very easy to do), so they just gave it to me like that and off I went in ignorance until I crawled underneath the Jeep three months later and happened to discover it.


Once my home mechanic was finally able to bleed all the air out of the lines (which took two efforts), it finally all works beautifully now.
12-29-2012 03:34 PM
texasjeeper1 BKeith5,

Sorry to hear about your troubles! I went through that situation not too long ago. Except I was going to drive somewhere and notice my clutch would not work. I paid around $1600 for my clutch replacement. It would have cost $1000 but I had the mechanic put in an aftermarket clutch assembly.

Is $750 the OTD price or just for parts?
If that's is the OTD price then I say go for it
Good luck!
12-29-2012 03:27 PM
DBJeep A clutch is meant to connect and disconnect the engine from the transmission. Letting the clutch pedal out moderately when starting motion or changing gears is fine. That is what it is all about.

Heat kills clutches. Heat happens when the clutch slips. Using the clutch to control speed on the trail or to hold position on a slope (trail or street) will kill a clutch because a lot of heat will be generated. Slippage also causes wear on the flywheel and pressure plate. Minimize slippage and the clutch will last a very long time.

Good luck with your new clutch.
12-29-2012 03:08 PM
bkeith5
Saving my clutch

The other day I was driving on the highway and taking an exit and my clutch popped and would not engage. Luckily I broke down near a mechanic and he told me the clutch and flywheel were pretty much gone. My first question is he gave me an estimate of about $750 for the new clutch and a couple other minor replacements saying it could go up or down, is that about a good price?

My second question is what are some ways to save my clutch in the future? I have only had my TJ for 3 years and there is less than 50,000 miles on it. I do take it mudding and trailing a fair amount so I assume that adds stress on it. Another thing I heard was that you should minimize riding the clutch and instead get in gear quickly, I have noticed that I will sometimes ride the clutch a while to make transitions smoother but should I stop that?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:45 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC