|09-09-2013 01:15 PM|
|PRWhitby||Mine was not pre-painted. There a few blemishes that needed minor body work before it was ready for paint. When it was, it was with the hinges off. There was no apparent paint damage to the bolts nor hinges because of the take off/put on process.|
|09-08-2013 12:34 AM|
|blawrence||The instructions call for the hood to be test fit so the hinges can be tightened down, then tremoved and painted with the hinges already on. If you order the hood per-painted, how does that work out when you install it? The factory hinges are painted on the factory hood, I assume there is damage when they are unbolted and lifted.|
|09-02-2013 10:25 PM|
|jwilson2598||I got $100 for mine from a local guy who picked it up.|
|09-02-2013 04:02 PM|
|PRWhitby||I tried Craigslist for mine; Put it out there for $200. Only 1 moderately serious bite, but the guy wanted it for under $100. Said that you could buy new hoods on eBay for way less (plus free shipping). I tried to explain that the one he was referencing was NOT an OEM hood, so you really couldn't compare apples to apples. Not even sure about how they could do that free shipping. Mine cost $90 to ship from the Detroit area to the Chicago area. So, currently mine sits, mounted way up on my garage wall resting on a few padded J hooks.|
|09-02-2013 02:44 PM|
|ArcticEOD||Ill let you know soon. I kept the box and packing material from the AEV hood to pack the old hood in when it goes to eBay. Ill probably throw it on for a couple hundred and see what it does.|
|09-01-2013 07:23 AM|
|bbermann||What are you guys doing with the OEM hoods after installing an aftermarket? If you are selling them, it would be nice to know what you are getting so I can figure that into the bottom line for the conversion.|
|08-31-2013 08:53 PM|
|08-31-2013 06:30 PM|
|ArcticEOD||The hood went on WAY easier than I imagined. Took the wife and me less then an hour. It arrived pre-painted and except for a few small scuffs Im sure I can get off with a little effort, I'm very pleased with what arrived; looks awesome!|
|08-30-2013 09:50 AM|
|Mopar2Ya||I haven't noticed any issues w/water in my engine compartment. The hood definitely lets heat out, you can see it when stopped. IMO the heat reduction is as good for the 3.6 as any engine, because modern engines run hot thanks to emissions(IMO hot is over ~195 deg).|
|08-29-2013 08:20 PM|
|ArcticEOD||My painted hood arrives tomorrow from Q-tec. The Old Lady and me are getting some Blue Moon and putting it on! Can't wait.|
|04-22-2013 02:42 PM|
|04-21-2013 09:48 AM|
|04-21-2013 01:25 AM|
How tough was it to install? Did you move the sound insulation?
|04-20-2013 06:51 PM|
|04-20-2013 03:04 PM|
|04-20-2013 01:58 PM|
Got my new hood painted and installed.
I tried to order through Quadratec, but their system still only reflected the old model (with only one washer nozzle). When I did an online chat with them, the nice guy told me to call and place the order, then tell them to order the new model. So I took his advice, but the guy who took my call kept telling me that they only carried the old model, and wasn't at all cooperative. So, I ordered directly through AEV. Did cost $130 to ship from Wixom, MI to a NW suburb of Chicago. Showed up in 2 days.
The body shop did an excellent job of matching my Gecko paint.
|04-20-2013 12:30 PM|
|04-20-2013 11:10 AM|
|blw2000||Do the pentastars run so hot a heat reduction hood is really warranted? It gets over 100 degrees here in Oregon in the summer sometimes, so I'd be concerned if they have a heat issue...|
|04-20-2013 12:11 AM|
|04-16-2013 06:03 PM|
It lets in less water then you think. The front vent is over the empty space between the radiator and the engine and the side vents don't seem to allow much water in at all. The holes are small enough that the water beads roll right off of it. Hardly see any water get through even when using power washer at the car wash.
|04-16-2013 11:19 AM|
What about the rain?
I'm in the market for a new JK, and saw one on the lot with the AEV hood. The vents allow rain to fall directly into the engine compartment - this seems like a bad idea! Especially here in Portland!
|04-15-2013 09:15 PM|
|MichiganJeepster||AEV builds exellent products right here in Michigan. I will be picking up a hood this spring just because they look so kick ass. I have their 2.5 " Lift with geometry correction brackets, Pintler wheels in Argent color and rear tire carrier. Great products and a great company. I will support this local shop as I live only 30 miles from their Wixom facility. AEV hood is heavier gage steel and is supposed to eliminate flutter according to their website. I believe you can order the Mopar power buldge hood which is an AEV hood without the vents if you like that look,|
|03-05-2013 01:22 PM|
|03-04-2013 11:45 PM|
I too was looking at geting an AEV hood eventually, but decided Id just get the inserts instead. Cuttin a big hole in a perfectly good hood just sounds like way too much fun!
|03-04-2013 10:50 PM|
|03-02-2013 02:37 PM|
|03-02-2013 01:48 AM|
|03-02-2013 12:14 AM|
|03-01-2013 12:54 PM|
|carguyco||Thanks for the thumbs up during this thread to my dealer....I have worked here about 6 years and appreciate the nice talk|
|03-01-2013 02:58 AM|
|res1971||When I called Pekins about a lift, the parts manager stated they stoood behind only AEV, and not Terraflex. I wanted Terraflex, but after being convinced I went with AEV. I would like to research this RK hood, but I don't think carbon fiber would look good on a Cosmo Blue Jeep! As far as the front and rear bumper combo, I am pretty much sold on Rugged Ridge; one for their pricing on Extreme Terrain vs Quadratec. Big price difference there, and they offer military 6% discount. I bought my first Jeep from Faricy. Great sales team at the time, but service department lacked big time. Perkins is by far the best dealership I have ever been to.|
|This thread has more than 30 replies. Click here to review the whole thread.|