|02-16-2013 10:30 PM|
|02-16-2013 09:34 PM|
|02-16-2013 09:06 PM|
|GSPup||Seriously looking good !|
|02-16-2013 08:56 PM|
Make some skids for those arm brackets on the frame.
If you ever wanna sell that rig, I get first bid.
|02-16-2013 04:39 PM|
Okay, I know I haven't posted progress in a while but I was busy working on little stuff and reassembling and today it went for it's first test drive. Everything is working pretty well just a few adjustments needed. Still need to modify and re-install the belly skid plate and the diff skid plate and paint the new hardtop. Here are some pictures that I just took today:
It's nice to be driving the Jeep again, it only took 2 months!!
|01-21-2013 08:18 PM|
|01-21-2013 08:01 PM|
Decided to use JK turn signals up front and finally got around to drilling the holes, got them wired and all installed.
I really like how they look and the same plugs for the stock TJ turn signals plugs right into the JK lights.
|01-19-2013 02:44 PM|
|jasongind||That thing looks sweet, until the first good trail anyhow lol.|
|01-19-2013 01:29 PM|
|01-19-2013 11:51 AM|
My new Poison Spyder Bombshell diff cover for the front axle.
|01-19-2013 11:48 AM|
Here is a picture of what you are looking for, one thing with this setup is it keeps the caster angle correct through the entire range of motion.
|01-19-2013 07:03 AM|
|Tshields||It's not the system that I would have used if I was adding the 44 to the Jeep, but it seems to work pretty well and hasn't caused any problems in the 9 years or so that it's been on. It definitely does not limit the Jeep at all.|
|01-18-2013 08:02 PM|
|01-18-2013 08:00 PM|
I'm just sayin that if the arms are spaced 6 inches instead of 12 inches, that makes everything have to work harder to keep the axle in place.
|01-18-2013 07:44 PM|
Parallel control arms are what you want. Smooth on the highway, tucked from the rocks, and more than enough droop. A long parallel upper does no harm. Only absorbs energy better than shorter arms. I'm not sure what you mean by axle wrap? That's a term commonly used with leaf springs. The axle can't really push forward of its normal position with 4 control arms holding it in place? I might be confused on your choice of words though.
I think his setup is beautiful.
|01-18-2013 07:20 PM|
Yours look almost parallel along their length. Seems like it would alter pinion angle with a change in axle position. I can understand getting the lower arm up behind the axle to increase ground clearance. But it seems to increase the chance of axle wrap, or camming over, and even torque in the brackets.
But I love that rear end set up. I need to upgrade from stick welding. Takes to damn long.
|01-18-2013 07:06 PM|
|Tshields||I'll get some pictures for you this weekend. They were done by the original owner when the Dana 44 was put in around 9 years ago. This Jeep has wheeled a lot since it was done with no problems at all.|
|01-18-2013 06:49 PM|
|01-18-2013 12:58 PM|
|Tshields||You looking for pictures where they mount on the frame or on the axle? I only added width to the frame bracket, the one on the axle will be much harder so still running heim joints there.|
|01-17-2013 09:09 PM|
|Full Spool||How about some pictures of the front diff control arm bracket relocation? Seems like.... with them so close together they would be more susceptible to wanting to tear off of the diff.|
|01-17-2013 08:50 PM|
Looking awesome man. Wish I had the abilities to do that type of work. Keep up with the pictures.
|01-17-2013 02:52 PM|
Your always welcome to come on by and help or just hang out. I'm running parts to the painter Saturday morning, should be back around 2 or 3 to start cranking on the Jeep again. Should be working on the Jeep all day Sunday and Monday. Let me know if you want to come by.
|01-17-2013 12:08 PM|
Nice work Terry! I can't wait to see it in person.
You gonna be around this weekend?
Need any help now that most of the hard work is done?
|01-17-2013 11:36 AM|
|jasongind||Nice progress man.|
|01-17-2013 11:12 AM|
Fenders and rear armor have all been modified and are ready for the painter. Hung the new doors tonight and got them all aligned.
Also got my parts back from the powder coater today so now it's time to start assembly for good, I think I'm finally on the down hill side now!!!
|01-14-2013 09:52 PM|
|Kyvman||Exceptionally nice work. Wish I had even 1/4 of the skills necessary.|
|01-13-2013 11:43 PM|
|Tshields||There is no cutting involved in the rear 1/4, just need to make sure you have good paint between them. The ones I'm installing are aluminum so they won't rust.|
|01-13-2013 07:43 PM|
|Full Spool||I've always wondered about those 1/4s. I guess it's best to put them on before you crunch a stock 1/4 panel. How do you keep the original skin from rotting out underneath an aftermarket. Or is it cut off, and there is no skin underneath. My ol'lady would kill me if I removed a perfectly good set of 1/4s. She won't even let me remove the smitty nurfs.|
|01-13-2013 07:30 PM|
|Oldguy||No kidding, I won't even think about working on my Jeep in the winter unless it's at least forty degrees outside|
|01-13-2013 12:06 PM|
Now I see what your secret is....You have a heated garage.
Try those mods in my garage and you will give up before you get the jackstands set.
|This thread has more than 30 replies. Click here to review the whole thread.|