Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Shifting the transfer case????? Problem?

Join Wrangler Forum Today


Thread: Shifting the transfer case????? Problem? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-21-2013 05:07 AM
jkjeeper06 Stopped works some times. Rolling very slow works all the time. That's why it says it in the manual. 4low is unsynchronized so which is why 1-3 works. Sometimes stopped the gears won't mesh. I find if I roll and the second before the vehicle stops moving, that's the best shift
01-21-2013 05:01 AM
Con Artist
Quote:
Originally Posted by JoshuaTreeRocks View Post
I just bought a 2013 Rubicon and the owners manuel is terrible. The first time I shifted the transfer case from 4L to 4H, following the instructions of rolling at about 3mph with the clutch in, there was a terrible gear noise and a clunk. Is this normal? Also, is it Ok to shift from 4L to 4H and vice versa with the vehicle stopped? It does not mention this in the manuel or video.
That's because the gears weren't lined up. Mine also did that the first time I put my transfer case in 4L.

1. Depress the clutch and put the vehicle in Neutral

2. Keep the clutch depressed and shift the TRANSFER CASE from 2H to 4H with one good, firm motion. Make sure this goes smoothly.

The transfer case has sort of a "zig-zag" when going from 4H to 4L. This is probably where you're getting "caught up" and winding up with some grinding noises. IMO, just completely STOP the vehicle instead of rolling.

1. Depress the clutch and put the vehicle in Neutral

2. Keep the clutch depressed and shift the TRANSFER CASE from 4H to 4L. It WILL work smoothly, it's just a matter of "finding" that "zig-zag" pattern. It took a few times for me to get it down.

I wanna say that once a week before I leave my driveway, I will engage the 4H and 4L prior to leaving, just to "line up" the gears or keep things "loose." I'd recommend doing this but I DO NOT turn the steering wheel, especially on dry asphalt.
01-21-2013 04:30 AM
JEEPDON From your post, I take it that you have a 6 spd manual tranny. If so, try this--- stop the vehicle and pit the tranny in neutral and engage the clutch---then, with the tranny turning in neutral, in one smooth motion, move the TC lever to 4h. NOW you can feel the way you have to manipulate the lever around the detent to get from 4H to 4L. Again, one smooth motion, move lever from 4H to 4L. Once you get the feel of it, you can shift this way from 2H to 4L. And once things get "broke in" it will shift a lot smoother. If you have an auto. try doing the same thing with the vehicle stopped and the tranny in N.
Above all, do NOT try to force the lever, or you will probably break the plastic bushings on the ends of the cable linkage and have to replace them.
01-20-2013 11:16 PM
JoshuaTreeRocks
Shifting the transfer case????? Problem?

I just bought a 2013 Rubicon and the owners manuel is terrible. The first time I shifted the transfer case from 4L to 4H, following the instructions of rolling at about 3mph with the clutch in, there was a terrible gear noise and a clunk. Is this normal? Also, is it Ok to shift from 4L to 4H and vice versa with the vehicle stopped? It does not mention this in the manuel or video.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:09 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC