|03-03-2014 01:20 PM|
|03-02-2014 09:17 AM|
|Burndog||This lift with 35" Duratracs will rub something awful on the back fenders. I'm in the process of adding bushwhacker flat fenders to solve the problem.|
|03-01-2014 12:20 AM|
|tugboatcaptain||I am also interested in doing this lift on my 13 JKU Rubicon. I will be running 33's 90% of the time and throwing 35's on when I go offroad. Question to those of you who have this lift on your 4 doors, are the 285 70 13 Falken Wildpeak tires on MT Classic rims going to look too small with this lift? Some lifts claim 2.5 inches but you can end up with more. I also have a Posion Spyder front and rear bumpers, Ace Rock Sliders and. Rock Hard Skids weighting it down. That's my biggest concern right now.|
|03-11-2013 10:41 PM|
|03-11-2013 10:39 PM|
|03-11-2013 10:26 PM|
|JOCJK||I just installed the RK 2.5 flex and definitely did not mess with the transmission skid. Cant imagine you would have to with the max travel just to put rear lower CA's on.|
|03-11-2013 09:46 PM|
IF anyone else has put this 2.5 Max Travel kit on their JKUR please post back and let me know if you had to remove your transmission skid bar.
|03-11-2013 04:24 PM|
|03-11-2013 03:01 PM|
Same kit now installed on the same vehicle (2013 JKUR).
Happy with the results, no issues to date.
|02-21-2013 12:21 PM|
|JerryJeepster||Rubber hose around the shock post with a pair of locking pliers and a wrench. Easy peezy|
|02-21-2013 12:18 PM|
this is my wifes DD and want it to be secure and safe,
i also asked the offroad shop that is doing the alignment if they could also doubled check the Jam nuts for me. i got them as tight as i could on the ground with a wrench.
but yeah had to trim plastic from passenger side and also modified a allen wrench to make it short enough to hold into the shock.
|02-21-2013 11:05 AM|
|paleh0rse||My front axle was off by about 1/2" using RK's numbers, so I took it to get aligned just in case. Like Kramer, though, my dumb ass forgot to ask for a print out after...|
|02-21-2013 10:53 AM|
In my case the lift came with a new front TB, tie rod, and adjustable LCAs. So I dialed in my toe and caster when setting their respective lengths.
And I was the dummy that didn't even ask for a printout of my readings. Doh!
Adjusting the steering wheel takes a 14mm (?) wrench and 10 minutes of your time.
|02-21-2013 10:38 AM|
|JerryJeepster||This is true. I brought mine in for the allignment and was barely off. The measurements of the RK track bar are pretty dead on.|
|02-21-2013 10:33 AM|
You don't really need to pay a shop for an alignment unless you're curious about the numbers specifically. If you followed RKs specs and dialed in the lengths of your CA properly you shouldn't need an alignment. All they'll do is adjust your steering wheel.
If your lift came with a new tie rod you would have dialed that in too. You can do the alignment in your garage and save the money. I wish I had known that before paying $80 to the dealership.
I didn't know it was so easy.
|02-21-2013 09:05 AM|
|JerryJeepster||That's why I let my son handle those. I cut out the plastic on the passenger side for access to the top of the post. He did the rest with a friend.|
|02-20-2013 11:59 PM|
Well it was snowing out side this morning...and the cold concrete about killed me, well the Lift is done i will post pics tomorrow, taking it to work to hopefully get it aligned at an offroad shop.
the biggest pain in the but in the whole thing was probably the front shocks.
|02-20-2013 03:37 PM|
|JerryJeepster||I here you. I'm south of Tampa and it got down to 60° for a low when we started my lift. Then it was shorts and t-shirts the rest or the day. Lol|
|02-20-2013 02:47 PM|
|hothondaguy||Getting there...rear is done...front is mostly apart....have to take breaks here and there because it is cold and working from home..... heheh|
|02-20-2013 10:00 AM|
Mine also took some finagling to get everything lined up.
|02-20-2013 02:47 AM|
|JerryJeepster||It was a pita to get it all to line up. Factory bolt goes in the bottom and supplied bolt goes in top and through the track bar. We had a lot finagling to do but eventually got it.|
|02-20-2013 12:42 AM|
well i have finally recieved my lift....
i couldn't wait to install it, it was hot from my wife driving it so i started in the rear. i ran into an issue with the rear trackbar bracket, my dad will probably assist me in the morning, but it also doesn't seem to get to close to the axle housing which concerns me. but also having issues with the Long bolt(former track bar bolt) and the new top bolt they have you drill and install.
anyone have any issues with these?
|02-11-2013 11:58 AM|
i just wanted to thank everyone for their input, it is greatly appreciated, hopefully i will be getting my lift later this week or early next week.
i will be printing this up and have it handy for review later.
|02-03-2013 08:57 PM|
Make sure your arms are proper length by putting a bolt through both ends to line them up when you think they are both at proper length.
Make sure when you route the brake lines properly behind the shock and don't for get about that ABS line as well.....
Here is the latest Rock Krawler directions. http://objects.dreamhost.com/rockkra...STRUCTIONS.pdf
|01-31-2013 04:14 PM|
|01-31-2013 04:09 PM|
|slowjeep||I just installed the same kit on my 2012 a few weeks ago. The biggest pain was installing the passenger side shock. Had to cut some plastic to access to tighten. I also burned up 2 different 1/2 inch drill bits on the sway bar holes before I finally just reused the stock bolts. It took 2 of us about 7 hours including a break for some pizza.|
|01-31-2013 04:02 PM|
|01-31-2013 04:00 PM|
A couple of tips:
1) Don't fully tighten the suspension pieces until the Jeep is back down on the ground.
2) Don't forget to center your steering wheel afterwards (suggest using a ProCal)
3) Don't forget the Red Loctite in the places where it's needed
4) Don't be afraid to add the Northridge4x4 JK Grade 8 Hardware Upgrade to the mix -- drilling out the RK bushings to 9/16" only takes a few minutes if you do it correctly, and it is certainly worth it.
5) Your front axle may no longer be centered after the lift, so the front trackbar may need additional tweaking to get it right. If you don't know how to measure for this, just ask!
6) You're going to hate the way RK wants you to install the front brake lines they send you... more info here:
Possible serious problem with RK's front brake lines installed on '11-'13 JKs
7) You'll need a really good torque wrench!!
8) Don't forget to get the rear trackbar relocation bracket welded into place ASAP after the lift install -- and definitely before you take it wheeling!
9) Pay close attention to front vs. rear control arms so you don't mix them up. When installed correctly, the words Rock Krawler should face outward and read correctly left-to-right.
10) Take a highlighter and go through the instructions highlighting only the parts that apply to the 2.5" Max Travel kit. (Their instructions include steps for every RK kit, all mashed together in a single list, so they're a f'n mess!)
11) Take lots of pictures and post them here when you're done!
12) Stay safe, have fun!
|01-31-2013 03:46 PM|
|hothondaguy||Yes i have those on their way with the lift...and wheel spacers because i am keeping stock wheels for now but upgrading to some used 35s at this point... and bilstein shocks|
|01-31-2013 03:09 PM|
|This thread has more than 30 replies. Click here to review the whole thread.|