|03-05-2009 10:38 PM|
|87YJWrangler||Yeah U joints are like $12 Hub is like $120|
|03-05-2009 10:37 PM|
|jpdocdave||ya bearing is the whole hub assembly, my old ones aren't worth using, same with u joints. u joints are cheap though.|
|03-05-2009 10:34 PM|
|87YJWrangler||Um Clutch, front wheel hubs (just bearing but I heard you cant buy just the bearing), Front U joints, instructions on how to go from hydraulic to mechanical clutch, brake lines and the list goes on but Im to damn broke to buy any of it|
|03-05-2009 10:30 PM|
|jpdocdave||i've done it and no one responded. let me know what you need.|
|03-05-2009 10:29 PM|
|87YJWrangler||I want some damn bump stops lol I'm sick of possibly smashin my oil pan again lol|
|03-05-2009 10:27 PM|
|87YJWrangler||You should have a list of parts you have, so we can maybe take them off your hands|
|03-05-2009 10:26 PM|
what is it with you and those bump stops. forget about them.
i'm undecided about my seats, i'll probably re use them.
i have d30 shafts i just put u joints in, and the rest of the axle waiting for scrap, as well as the non c clip d35 waitin for scrap. lots of stock engine and driveline parts from a few 4.0 and 4.2 jeeps. some 4 banger d shafts and t case main shafts.
|03-05-2009 10:20 PM|
|87YJWrangler||Um never mind lol, got anything else like a clutch or maybe a set of seats for cheap? Or stock bump stops|
|03-05-2009 10:18 PM|
|03-05-2009 10:13 PM|
|87YJWrangler||Mine are practically flat if they are any better?|
|03-05-2009 10:11 PM|
|03-05-2009 10:08 PM|
|87YJWrangler||damn alright how much for the leafs? or maybe free?|
|03-05-2009 10:07 PM|
|03-05-2009 10:06 PM|
|03-05-2009 10:02 PM|
hey doc, got any of the vacuum parts laying around? 4x4 jumper switch or any of the other little vacuum stuff under the hood?
email me and i'll send you a pic of what i need. or, how do i send it here?
|03-05-2009 10:01 PM|
|87YJWrangler||Depends on price will the XJ coils fit my yj?|
|03-05-2009 10:01 PM|
oh yeah, low mile stock xj coils also.
|03-05-2009 09:58 PM|
|87YJWrangler||Got any springs?|
|03-05-2009 09:55 PM|
|jpdocdave||almost any stock part|
|03-05-2009 09:50 PM|
|87YJWrangler||Hey doc what other parts you got layin around?|
|03-05-2009 09:01 PM|
11 or 12 bolts? i have a few valve covers laying around. the bottom one is from an 87 4.2 and its aluminum. but it has 15 bolt holes like all the valve covers i have laying around.
|03-05-2009 10:14 AM|
|wouldwerker4u||I still haven`t had much luck! But I did manage to get some RTV to seal the hole as a temporary fix! Still looking for a new one!!!|
|02-26-2009 05:05 PM|
|87YJWrangler||Dude check autozone or napa I get all my parts from there and they ask if its a 90 because I tell them I cant seem to get it anywhere else and they have them on hand. Or liquid gasket|
|02-26-2009 03:31 PM|
Thanks guys , but from what Ive been told at Collins Bros. There was some kind of change up mid 1987 thru mid 1990. And just my luck I got caught in the middle of all that!
If either of you guys have one that has 11 or so bolt holes in it I would love to do buy one, especially after ordering one already that does`nt work from Collins Bros.( That one has only 7 bolt holes!) And I lost the cost of shipping when I returned it to them!
|02-26-2009 01:35 PM|
|87YJWrangler||If its the 4.2 you can use one from any 4.2 they are all the same engine as long as its the inline...|
|02-25-2009 08:19 PM|
|jpdocdave||i have a 4.2 valve cover from my 87. you're welcome to it, pm me if interested.|
|02-25-2009 04:44 PM|
Valve Cover Issues!!!
Okay,after cleaning all the gunk out from under the hood, I drove home (about 12 miles) and when I got home the top of the motor was covered with oil. After looking everything over I found a small piece of metal missing from the oil filler hole where the ears of the oil filler cap go into the valve cover. I used some RTV to fix the leak and started looking for a replacement valve cover. For some reason, no one makes one that will fit everything stops at 87 and starts back at 93. Mines a 1990 that came from the factory with a aluminum valve cover that has about 12 bolts around it. And an inline 4.2, if anyone has a good parts resource I would be very appreciative! I`ve tried JC Whitney, and Collins Bros. but I`m still loking!