Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Discussion Forums > Pictures Forum > Tiltz 2 door JK

Join Wrangler Forum Today

Thread: Tiltz 2 door JK Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-01-2013 10:19 PM

02-01-2013 10:16 PM

02-01-2013 10:15 PM
And some wheeling pics..

..Until I get more done on her.

Anyways, I hope that is a good start to being a contributing member

02-01-2013 10:08 PM
Some of the parts accumulating for the stretch


Some towers I had a local guy CNC for me
02-01-2013 10:05 PM
The most awesome thing yet

I am a novice fabricator... here is my awesome custom license plate bracket.

02-01-2013 10:01 PM
Welding more stuff on...

Sliders used to be bolt on, but new long arm brackets didn't like where the sliders bolted up...

So mod them and weld them on.

Notice how the bracket wraps around the bottom of the frame

Chop off those lower mounts

Clean the frame and weld them on

02-01-2013 09:55 PM
Long arms up front

Ripped out the old... They are pretty small next to the Synergy stuff

Making it so the Jeep can never be stock again: (factory control arm brackets)

New bracket in place

Everything pinned up with the arms adjusted a little less than an inch forward

Approximation of the stretch
02-01-2013 09:48 PM
Lil stubby...

...that I built but sold.

02-01-2013 09:44 PM
Ruff Stuff Tie Rod

If you have a JK and need a new Tie Rod, I highly recommend the Ruff Stuff Specialties one. It is super simple to build and install. I went ahead and drilled out my knuckles for a tapered insert, but this step is not necessary. It just allows the taper to sit deeper so you can engage the cotter pin... Your call.

02-01-2013 09:39 PM
Front Axle Build

Axle removed from JK awaiting new parts

Drilling 24 1/2" holes for the inner sleeves.

Difference between old and new tubes.

Fitting the truss and track bar mount

Burning everything together

Puurtty and Burly

Everything pinned up
02-01-2013 09:32 PM
Tiltz 2 door JK

Hey Everybody, thought I'd share the project I am currently working on.

I am newish to the forum but not new to Jeeping

• 2012 2 door manual Rubicon daily driver
• 35 inch procomp MT
• 2.5” TeraFlex Coils and shocks
• Ruff Country front Bumper
• Warn 9.5TI Masterpull Synthetic Line and Aluminum Fairlead
• SmittyBilt XRC Carrier
• Shrockworks Rock Sliders
• Cobra Radio
• Front D44: Artec Truss, and Skids, Poly Performance C Gussets and Inner Sleeves, Alloys USA Ball Joints, Ruff Stuff Tie Rod, Synergy flipped Draglink
• Synergy front Long Arms
• Chopped up fenders, dings, NW pinstripes, broken taillight, crunched up stock skid plates

In the works:
8" Stetch
-8" Synergy stretch, which includes new arms, frame side control arm brackets, and a frame side track bar bracket. Stock bumpstops will be moved back 8."
-Coilover Towers will be set inboard on the frame and connected with DOM. The placement is the only thing that is really undecided. I might do some chopping to the cross member and mount direct above the axle. I might not. I bought the synergy lower control arm skids with shock mounts, so I do have an alternative shock mounting location. The rear track bar bracket looks like it will determine the shock placement. Either way they are going through the floor. I will probably gets some sheet metal and box around them so that the floor is still water tight.
-14" 2.0 remote resi King Coilovers - mount resevoirs to DOM cross member
-4 door e-brake cables
-Hard brake line relocation (maybe - I already replaced both stock rears and mounted them differently because my sway bar links didn't clear properly - they might work as is)
-Lengthen ABS wires, breather hose, locker wires,
-Either ditch the sway bar or it looks like it could be moved back on the frame. The only problem is that the frame is in a lower position. looks doable
-New driveshaft
-Cut off factory exhaust before axle and mount inline muffler and run straight back
-Limit Straps
-Trim sheet metal to allow for full stuff. I am going to try and retain as much of the corner as possible. I do not want to compcut. I will most likely run a modified stock fender flare until Poison Spyder releases their new custom corners.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:17 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC