Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 94 YJ won't turn over, tried everything I know

Join Wrangler Forum Today


Thread: 94 YJ won't turn over, tried everything I know Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-07-2013 08:09 AM
sevenservices good find!
02-07-2013 04:59 AM
Keymo It should just be out of adjustment if all you had to do to get it to work again was tilt the wheel.

The Starter (ignition) switch is on top of the steering column behind the dash - it's definitely a PITA to get to as well. I would recommend when you get to where you can actually get to the conenctions on the switch - take the plugs apart and clean all of the contacts REALLY well - then reconnect using dielectric grease.. The ignition switch is held in place by a couple of, I believe 5/16 nuts. Theres a push rod going from the key cylinder into it - when you turn your key the cylinder moves the pushrod into different position on the switch. This COULD be where your problem is. If it's out of adjustment, you may just need to loosen the nuts up and then push the switch towards your steering wheel a little bit. If I were you, I'd adjust it a little bit and try turning the key and repeat until if works without the wheel tilted or you can't adjust it any further towards the wheel. If you get it adjusted all the way and it STILL doesn't work - you very well might need a new Ignition switch.
02-06-2013 05:27 PM
mporado
Tracked it down...

It turns out it is in the switch somewhere. Not sure if it's a short; I pulled the tilt wheel down and it started every time since. I'm afraid it will be a pain to replace it.
02-04-2013 10:00 AM
mbaseel Randomyjguy sounds like bad connections. I had this happen. Had to clean every ground wire connection with a wire brush and then re attach. It worked for a couple of days and then stopped again. Turned out that my main positive wire from the battery to the starter was corroded inside the sheath. Replaced all main wires ( grounds and hots) and works like a charm now. Hope this helps
02-04-2013 09:41 AM
RandomYJguy When i turn my key, it clicks and then everything shuts off. Radio etc.

It doesn't crank or anything.
02-04-2013 08:32 AM
sevenservices does is go dead and stay dead? If it dies and stays dead, its your terminal connections.

If it goes way down, then comes back up to power when you let off the key something is jammed up somewhere...
02-03-2013 11:37 PM
RandomYJguy Some exact problem with mine... I am able to start the jeep by taking a screw driver (with rubber handle) and touching the 2 contact points on the starter solenoid. Starter tests out good, could it be just the solenoid..?!
02-02-2013 03:53 PM
rmloke1 Check the crankshaft sensor, knocked mine out of place last year and it sounds alot like what you're going through
02-02-2013 12:22 PM
Gunz n tractorz I'm sorry the first part should say tap starter with hammer.
02-02-2013 12:20 PM
Gunz n tractorz Then try to turn over again and repeat
02-02-2013 11:58 AM
teardropty Check your grounds and battery connections. A slight film of corrosion between a battery clamp and terminal post can give you a positive reading but break connection when you go to start. Make sure your battery posts and clamps are clean and making good contact. Put some dielectric grease on your connections. Also check your starter connections. Does the starter relay click at all?
02-02-2013 11:27 AM
mporado
94 YJ won't turn over, tried everything I know

I have a 94 Wrangler YJ, it won't turn over. switch is on it shows power until turning the switch then nothing, like dead. I have a new battery, tested the starter, replaced the cables, replaced the starter relay, still nothing.
i would appreciate any ideas, I don't know what else it could be?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:47 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC