Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Sliding window locks

Join Wrangler Forum Today


Thread: Sliding window locks Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-16-2014 01:36 AM
ProfesorZielony
Torx inbetween size

Hello,
I am looking forward to fixing my latches on the sliding doors.
The mentioned screws are security torx and come in various sizes, I grabbed a kit today and it has T15 then skips to T20.
Well the 15 is too small and the 20 is too large. Any chance you know what size I need or where to find one.
02-07-2013 10:26 AM
Rrampley Just the clip part is broken off both side the base is there as well as the little pins that hold the clip on to the base.
02-07-2013 10:09 AM
aikmanson
Quote:
Originally Posted by Rrampley
But what if there is no clip to take off?
Sorry didn't see your post on that, I was merely responding to the 'fix' for broken but complete clips. You could fab something up to act as a clip (like the stock one). The design is really simple, yu need a thin arm with a edge to catch the notch on the window. You also need a flat base for the spring to sit on the apply pressure, and two pins to fit into the base of the latch.

What part are you missing, the clip (arm), the base, or the whole damn thing?
02-07-2013 12:37 AM
Rrampley But what if there is no clip to take off?
02-06-2013 10:28 PM
aikmanson Hey guys I have experience with this as I fixed my sliders right after I bought my jeep last month. First off, bestop upper door sliders, clips were essentially useless and would pop out over bumps.

To remove them you need a torx bit with a hole in the center (tamper proof torx). You can get around this by getting a set of clamping pliers on there and turning the two bolts off. Be careful not to break or scratch the window, but it should be alright. Once you got the clip off you need to separate the two pieces. Push in on both ends of the "pins" and pull the clip from the base. Once apart yu will see there is NO spring!? Mine had a simple piece of plastic that was broken to the point where it did nothing. My fix was to buy 4 springs (1 per clip), and install them into the base. Put the clip back onto the base and reinstall.

Hope this helps, I can try to go into more detail if needed, but really it's self explanatory once you get them off and open them up.

Good luck!
02-06-2013 10:06 PM
Rrampley They were Best Top sliders the whole set upper doors. No parts for them I could find.
02-06-2013 09:38 PM
All Terrain JK
Quote:
Originally Posted by Rrampley View Post
On my latches on the slider window they say STEEL HORSE so I looked online and can't find any parts just the doors that sell for about $450 a set.
Steel horse is brand that either went out of business or was bought out years ago. I have a set and would love to buy another. Did you find some for sale or were they just bestop or rampage sliders?
02-06-2013 08:34 PM
Rrampley On mine the clip portion is broken off. Has been since I got the jeep last march...
02-06-2013 08:09 PM
scott howard just take them apart . They have a small piece of flat spring steel that if you just flip it over will work like new again.

If they are like mine and i am sure they are.
02-06-2013 07:43 PM
Rrampley On my latches on the slider window they say STEEL HORSE so I looked online and can't find any parts just the doors that sell for about $450 a set.
02-06-2013 07:26 PM
TheDefiled Same issue the front part will be fine but the back slider always opens and can easily slide it open to get into my jeep. A cheap way to fix it would be to duct tape it, but if there's a more permanent to open it that'd be better.
02-06-2013 07:24 PM
Rrampley X3 I need the latch locks for my sliders also
02-06-2013 07:18 PM
Grizzly74 Ive got the same issue with a 1997 TJ...so if anyone can clue me into where you can get the 4 locks. It would be greatly apprecited!
10-12-2011 01:20 PM
Xgrunt
Sliding window locks

Before I take them off and apart to replace what I assume is springs? Is it easier to just buy new ones and if so where? Mine won't stay closed and the windows slide open when driving.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:47 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC