Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Clicking noise help

Join Wrangler Forum Today


Thread: Clicking noise help Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-02-2009 06:49 PM
jpdocdave slight lifter tapping on jeep straight six is pretty normal. if it isn't real loud, or sharp sounding. honestly the first thing i'd do is buy some oil flush chemical, its really just keroscene. you put it in the oil run the engine for 5 mins. and then change the oil. i've seen it fix noises multiple times, and i used to be a skeptic of it. secondly is keep up on the oil changes. oh yeah, the longer you let it drain after the flush the better.
03-02-2009 06:45 PM
cap10 crunch Thanks Mopower! Your post has been very helpful!
03-02-2009 06:39 PM
YjMopower Here is some info about what is a lifter and a possible soultion .If the problem is lifter tapping immediately after cranking the engine, the oil check valve in the cylinder head may need cleaning. Page 17-10 in the shop manual covers the procedure.

The check valve is simply a spring-loaded ball in the oil feed line that prevents oil from draining back while the engine is not running. If this check valve doesn't do its job, the oil lines in the head will be empty, and they will require a few seconds to fill when the engine is started, causing lifter tapping.

The valve is located inside the valve cover, at the lower front corner of the head. After pulling the valve cover and finding the valve, locate the locking screw]\ that goes in from the outside of the head to the side of the valve, and loosen it about four or five turns. Screw (by hand) an M6x40 bolt gently into the valve spring guide (the only part that you can see) until it bottoms, then unscrew it two turns. Pull the spring guide out. Using a magnet, remove the spring and ball. Clean everything, being especially careful to avoid damaging the ball seat down in the hole. The book says to replace the o-ring, and it would be a good idea to do so, especially if it is hardened.

Reassemble. The threaded rod that screws into the side to retain the valve should be tightened to 2.8 ft/lb, which isn't much!

______________________
Engine Tapping Noise

Tapping noise from the engine is often caused by a stuck hydraulic lifter. A bad lifter is not necessarily a huge problem and if you are driving an older vehicle you may wish to just ignore the noise if the engine is otherwise perfoming well. Increasing the frequency of your oil changes may help to clear up the issue but if the noise persists you will need to replace the lifter to eliminate the sound.

The above noted, if your tapping sound is accompanied with engine vibrations or backfires, you may be facing a problem more serious than a stuck lifter.

1. Tapping and Vibrating
If the tapping in your auto's engine is accompanied by a persistent vibration or noticeable tremors under load, you may have damaged the rocker-arms or valve push rods. To check the problem you will need to remove the valve covers and visually inspect the arms, rods, and valve stems. Oftentimes the repair is nothing more than replacing the broken rod or arm and bolt.

2. Tapping and Backfire
Though much less likely, if your auto happens to also be backfiring while tapping, you may have a damaged camshaft. This will not be something you should attempt to diagnose yourself, and it will be a fairly costly and laborious repair. If you suspect a bad camshaft, take your auto to a reputable mechanic or dealer and get the cam tested. Before leaving your vehicle, get a full estimate (in writing) and for the repair itself, and for the testing and reassembly should you decide to decline the repair.

If you do go ahead and replace the camshaft, you should also replace all of the lifters as well. Further, this is an opportune time to replace your timing chain or belt.
__and this is what it possibly could look like.
Good Luck ,At least I learned something
03-02-2009 06:23 PM
tasherrill I've glad someone posted a question on this. Mine starting making the same sound, so I'm going to check out the fan right now.
03-01-2009 02:10 PM
cap10 crunch Well i went out and checked it and I had to drive it around the block to get the sound to come back and it's coming from the back of the engine right by the windshield. I feel really dumb asking this but what exactly is a lifter? I didn't see anything that could be making a noise.
03-01-2009 01:29 PM
cap10 crunch Thanks everyone. You guys have been very helpful. I will check the fan and the lifter later today and I will get back at you guys
03-01-2009 10:09 AM
Warlock Check the timing chain, mine was hitting the cover because it was worn out and sounded just like a lifter pecking.
03-01-2009 05:38 AM
yjtodd With the engine running take 3 feet of hose and put it to your ear and see if you can locate where the sound is coming from specifically.( Becareful to stay away from the moving parts- fan, pulleys etc.). Jeep in-line engines are notorious for a valve/lifter tapping sound- also try running a higher octane fuel w/ a good fuel cleaner and see if it lessens the sound any. I've also seen water pumps that are going bad make this sound as well. If you can isolate the sound area get back to us and we will give you some more ideas.
03-01-2009 05:00 AM
87YJWrangler My guess is lifter or maybe the fan is hitting so x2 on both above
03-01-2009 12:36 AM
distortedtj
Quote:
Originally Posted by amerijeep View Post
lifter tapping?
x2
02-28-2009 09:28 PM
amerijeep lifter tapping?
02-28-2009 09:02 PM
YjMopower it could be your wheel bearings or maybe your fan is hitting the housing it happened to me once.
02-28-2009 08:50 PM
cap10 crunch
Clicking noise help

Hello. I'm new to this forum and also a new driver Well i got myself a 1990 4.2 L YJ with 133000 miles on it and ive started to hear a clicking noise. It's constant and as i rev it gets faster and when its idled it becomes slower. It's really weird because if im stopped and its in neutral i can sometimes rev it and the noise just stops. That also happens if i get up to 2500 or 3000 rpms or it just goes away. The noise is like a metal fan slightly hitting something. It's basically as loud as my engine.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:42 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC