Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > BA10 to AX15 swap in a 91YJ 4.0

Join Wrangler Forum Today


Thread: BA10 to AX15 swap in a 91YJ 4.0 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-03-2009 09:59 PM
ks90yj They should be. But I'm not sure.
03-03-2009 09:29 PM
alaskanaddict
AX15 swap

Hello, do you know if the bell housings from YJ's and XJ's are the same? Thanks, Bill
03-03-2009 12:41 PM
ks90yj The ax-15 will bolt right up! Have fun its pretty easy If you can find the hard line out of an xj I also belive you will need to redo your master cylinder. Here is another page that a guy also did the swap he has pics and everything.


http://www.jeepforum.com/forum/showthread.php?t=312203


This is for all of you who are thinking about doing this swap. Its overall pretty easy (as long as you have the right parts) First things first get you a new can of PB cause you'll need it! Get you some little zip lock bags and a marker and be sure to label what parts you put in what bag. Next youll need to get an inverted torx bit its a m12. This is for the top two bellhousing bolts pain in the arss (I replaced them with regular bolts) Here is the most important one PIOLET BEARING!!!! before you even start call advanced adapters and have them send you the one for you tranny. Measure your AX15 inputshaft and it should be .75 or I forget what the other measurement was but measure it anywho. When you get it, it will be to big to fit in the back of your crank, so you can do two things either put it on a drill bit and grab some sand paper and start sanding yet another pain or (the method I tried after sanding) take it down to your local machine shop and have them get it the size you need (I took the piolet bearing from my new clutch kit and they sized it up). Next get a new clutch well worth it. My next recomendation is find you an external slave cylinder. I stuck with the internal but kind of regret it now. After haveing to pull the tranny back out after having it all bolted up and finding out it leaks like crazy if you dont put the o-rings in the lines . So go with the external slave. If you do that I believe you need to swap your master cylinder. Next get you a little hand pump for your t-case if you dont have one. Made filling way easier!! And last but not least have some good help around makes a hell of a difference!!!
Hit me up if you have any questions!
03-02-2009 10:23 PM
4point Welcome alaskan, I moved your thread to the YJ forum for more help.
03-02-2009 10:12 PM
alaskanaddict
BA10 to AX15 swap in a 91YJ 4.0

Hello, I need some help. I just bought a 91YJ that apparently came from the factory with the BA10, output shaft 23 spline to an np231, crazy. The BA10 was removed when I bought it but the mechanic swears that that was the trans the jeep had in it. I have the original bell that looks like it could fit the AX15. I found a really low mi AX15 from a 96 XJ, with the bell, original skid plate with a step in it that has 2 sets of slots. It seems that I may have to cut out more metal to make the newer AX15 and bell fit. The newer bell is almost 2 inches longer than the original. What the hell should I do? I'd like to swap to the external slave set up which is what the newer bell is set up for. Do I look for a hyd line for a YJ or an XJ? Has anyone out there done this swap? Thanks, Bill

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:42 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC