|02-17-2013 11:51 AM|
|02-17-2013 11:49 AM|
|02-17-2013 10:31 AM|
|02-16-2013 11:06 PM|
|LouieDelTorchio||So I got my hub out and brought it to autozone and found out it was a later version. Which I figured due to the 2 3/4 rotor depth. They had two duralasts for 65 each. I decided to order two timkens. Theyll be there thursday. Got them for 100 each. Now I just have to take my other hub off then wait till thursday.|
|02-11-2013 02:18 PM|
|Jerry Bransford||Measurement of Rotors|
|02-11-2013 12:16 PM|
|02-11-2013 12:11 PM|
|doclouie||If you want you can also measure the rotor hat depth and it will let you know if you have an early or late model wheel hub assembly. 3" is mid 99 or older and 2 3/4" is mid 99 or newer. Look at Savvy' s website on rotors and you will know exactly what I mean.|
|02-11-2013 11:20 AM|
|02-11-2013 11:13 AM|
|LouieDelTorchio||Alright well I'm going to start taking the hubs off today. Ill let you all know how it goes|
|02-11-2013 10:16 AM|
This will help... D-30 Axle Shaft Removal - 1
Stu's website has a plethora of useful how-to information for TJs.
|02-10-2013 09:56 PM|
|LouieDelTorchio||Also remember I have no experience with this haha.|
|02-10-2013 09:53 PM|
|02-10-2013 09:51 PM|
|LouieDelTorchio||How long does it usually take to change out the hub assembly?|
|02-10-2013 08:25 PM|
|Patrick H||Murphy usually enters here for me. If I just replace one, the other one seems to fail shortly after. It's probably just my luck though.|
|02-10-2013 07:01 PM|
|Jerry Bransford||Not precisely at the same time, no.|
|02-10-2013 06:58 PM|
|LouieDelTorchio||Also, is it normal for both front bearings to go out at the same time?|
|02-10-2013 06:43 PM|
|LouieDelTorchio||Alright sounds like a good idea. Thanks Jerry, youre always helpful|
|02-10-2013 06:15 PM|
Whoops you have a '99 which changed unit bearing hub dimensions in the middle of the production run. So it's going to be hard to know if you have the early or the late version of the 1999 unit bearing hub and they are definitely not interchangeable.
Instead of ordering from Rockauto.com who I order from on a regular basis, I would instead remove one of your unit bearing hubs and take it with you to your local auto parts store & make sure you get the right hub. Sitting them next to each other & comparing their height differences is the only way to know for sure if you're getting the right version.
Installing the wrong unit bearing hub will lock the wheel up.
|02-10-2013 06:15 PM|
|02-10-2013 06:11 PM|
|Jerry Bransford||Need to see Rockauto's page that shows the Timken part number.|
|02-10-2013 06:08 PM|
Is this the correct one? Rockauto says it is but I just want to make sure. Sorry about all the questions.
|02-10-2013 05:58 PM|
The hub's retaining nut was torqued by the factory & then locked in place by a nut holder which is locked in place with a cotter key. In other words, the nut couldn't have loosened on its own where simply retightening it would be the correct fix. Unless someone has removed the nut and didn't re-tighten it back properly, and since you say the tires have been properly balanced, it sounds like your fix is pair of new unit bearing hubs.
|02-10-2013 05:50 PM|
|02-10-2013 05:49 PM|
|02-10-2013 05:43 PM|
|LouieDelTorchio||I had the tires balanced twix e by rwo different places. My dad said something about being able to tighten the nut on the hun assembly. He doesnt know too much about jeeps but could that be the problem?|
|02-10-2013 05:36 PM|
A speed-sensitive wobble invariably makes me immediately think bad tire balance, or at least imperfect tire balance. But a bad bearing is possible too. Our TJs use what is called a "unit bearing hub" which is non-serviceable, it is replaced as a unit which is a fairly simple job. Timken is a desirable brand of unit bearing hub. At the very least, I would first have the tires very carefully balanced by a good tech who knows he needs to take a little extra time on your tires to try to solve a problem.
By itself, a bad alignment will not cause a shimmy or vibration.
|02-10-2013 05:30 PM|
|Horn5413||You have to replace the wheel hubs. You can't repair them.|
|02-10-2013 05:09 PM|
Alright so I've had this bad wobble at 40-45 for a while now, and I've checked the steering components and such for some loose bolts but it all seemed good. Then, I noticed my rear trackbar was loose so i tightened it, but still the problem remained. So i was reading about bad wheel bearings, and they say the test is to wiggle your tire when in the air. Mine has some play in it, not a lot, but some. I then put my tire on my brother's TJ just to check and there was absolutely no play in it. Both sides of my front axle have play in it. I'm wondering if this is my problem? If it is, is there anyway i can fix it or do i have to buy new bearings? I've heard you have to buy the whole hub assembly. Also, I think my alignment is off, but would that cause a severe wobble?