|03-22-2009 08:05 PM|
had time to work on the cover a little bit today. i was only able to make the rear section...but i made it way more solid than i'd originally planned.
then after i got the 1/8" cut and welded to the rear i sat a scrap piece on it for a mock up...not sure of how im going to attach them yet...i could always weld it, but i have about a dozen stainless countersunk bolts laying around that match the ones on my rear bumper...idk
|03-21-2009 01:18 AM|
redid the shocks with a millermatic 251:
|03-17-2009 11:23 AM|
|NalinMFG||the only problem ive ran into is the upper shock mounts. you dont have much room on the frame, and the crossmember where they used to be mounted on is gone. mine were at a pretty hard horizontal angle and bent my bracket/broke my weld... im going to see about coming up with something better.|
|03-17-2009 12:16 AM|
|ygohome||thats looking really good so far. I was going to see about having a shop do something similar... but its a lot of work it seems. Right now my tank is sitting in the tub and will probably stay there. someday maybe we'll sink it.|
|03-14-2009 03:40 PM|
oh and i did end up having to get new filler hoses
the larger one is 1 1/2" ID and the smaller one is 3/4" ID (i bought a 5/8" and a 7/8" and made the 5/8 fit...its definantly a little small though.)
re aligning the plastic trim piece was an EXTREME PITA!!! it might just be for me though because i cut the hoses the exact length and had no room for play.
i found that a chop saw makes the cleanest cut...the walls on my 1 1/2" are 1/4" so pruners were out of the question.
|03-14-2009 03:34 PM|
billavista has an excellent tech section on fittings/auto plumbing.
the vice just makes life a little easier.
last night i started it up and drove it around for a little bit
today i switched my ratchet straps back to the origional black ones because i can make those alot tighter. my exhaust pipe was pretty close to my passenger shock so i went and picked up a hanger thingy from advance so pull it away.
i noticed when i close my tailgate with the top on the wheelwell area where i cut(right above my new upper crossmember wants to flex a little and make a creeking noise. i got some caulking and let loose the whole tube where my body rests on the crossmember and boogered the corners of it. its hardening right now so ill see if that fixes it.
its also parked up on a cinderblock right now, i know thats not much flex, but it gave me a good enough guage to see that my track bar should still have planty of room.
its raining and the jeep is in the driveway so i didnt take any pics today.
|03-14-2009 11:42 AM|
|YjMopower||Nice Work, why exactly did you use that vice grip thing , you couldn't get them in?Thanks for the link it really helped a lot. Keep it coming|
|03-13-2009 04:03 PM|
the hose got here a little while ago, putting it together:
installed on the fuel pump:
got the hoses off. it felt like the rivet went through the plastic part as well, it actually only goes through the hose clamp. im not sure if i need to shorten these of not yet...its pretty close.
incase i need to get new ones the ID of the smaller hose measured 7/8" and the larger on came up 1 5/8".
i need to do some work on the drivers side shock, get those filler hoses finished, and it shold be good for a test drive.
|03-13-2009 12:25 PM|
also, if the welding pirce is high, summit has a nice fuel cell that will fit behind your seat and you dont have to do any of this.
but the only reason i didnt go this route is becase you need to buy a fuel ring($100) and cut the tank. you then need to get more russell fittings and hose to connect to the threads provided on the tank...probably another $100 after all said and done. if i need more room one day i will upgrade my setup up to this(ony mine will be sunk into the tub ) its just ALOT cheaper this route and i get the satisfaction of knowing that i did everything.
i opted to cut my 4x8 sheet down the middle at 27" and now my wood top workbench is now metal...so now i only have a 19" x 8' section to play with. i found it more important to stop catching my bench on fire than to not look at my gas tank for awhile. this should give me more time to decide on how i want the top to function.
|03-13-2009 12:07 PM|
at the top of the page i have a link called "YJ". you may want to look at his build since it'll be more accurate to what your're doing. i dont know how much more it would cost since someone else is welding, but since you have no rear mounts, you could tie the frame into the cage like the guy on the "TJ" link did.
haha the hoses are stayin like that! i had put the carpet side walls back down to see where i needed to cut them. they go through the carpet back to the factory fill location. i havent dont that yet, but i will post up pics when i do. FedEx should get BY 4:30 according to my tracking, i wont be working on the Jeep until those get here since its back down to 30* again
i also posted this build on Pirate, there are discussions on there that we did not have on here if those would help you any.
|03-13-2009 11:28 AM|
|YjMopower||Nice work of art , for those necks though they look like there struggling a bit, only suggestion i have is maybe cut the hose in to separate parts and you some elbows? I think I might Do mines tomorrow ,Depending on how much the welder charges me.I have to use some long thick metal block where the rear tub mounts are at each end.unfortunately my tub doesn't have the rear mounts so i kinda got to make a place to screw in to them.I was thinking once i get that block just drill two holes where the tub mounts are then drill a whole in the tub and use long screws with nuts and washers to hold it all together.|
|03-12-2009 04:45 PM|
in and waiting for JEGS to get my fuel hose/fittings here...
still need to work on the filler necks...i think i might take the head off, find the ID and just get some new ones if they give me trouble
|03-12-2009 08:19 AM|
there is definantly nothing on either hose(well plastic piece...not sure of the terminology). both the filler and the overflow coming into the tank about 1.5-2" and are solid plastic.
|03-12-2009 03:11 AM|
|jdhallissey||On the tank full ball there should be a hose running off of it.|
|03-12-2009 01:19 AM|
|03-11-2009 09:17 PM|
|03-11-2009 09:09 PM|
|03-11-2009 08:33 PM|
|YjMopower||Talk about serious skills,i need to learn how to weld.Its coming out better than i expected.Did you think about putting a flat piece of sheet metal underneath to avoid the slight liltle rocks hiting it?|
|03-11-2009 06:30 PM|
tabs on + some paint
|03-11-2009 05:22 PM|
scrap being made into tabs for the ratchet straps
|03-11-2009 05:16 PM|
|NalinMFG||hmm...i think now would be a pretty good time to do the 15 to 19 gallon fix...|
|03-11-2009 05:09 PM|
i have it fully welded now, but here's a pic tacked.
it looks like its only going to stick up 5 1/2" before i put a cover on. i used 2" tubing so if you used 1" or flat stock it could be as low as 3 1/2"...i like the beef of the 2" tube though.
it turns out the fuel fittings are different sizes on each end. one is 3/8 and the other is 5/16. i went ahead and ordered the stainless braided stuff from jegs. summit was out of one of the fittings so i opted for jegs even though they cost a hair more.
Russell #799-610020 you will need 2 of these
|03-11-2009 02:00 PM|
|YjMopower||Nice Straps ,on What is it sitting on did you make a crossmember just for it?On my gas tank those two things at each end are not connected to anything what exactly are those things for?Nice Job on The T connections|
|03-11-2009 12:18 AM|
decided on my bracket design, made the passenger side, and welded it up:
cut hole for filler hoses. i should just have to shorten them:
trimmed a little more tub and put another corssmember in (some type of upper crossmember to replace the floor supports will be needed):
the barb on the breather hose broke so i had to get a new one. of course lowes dosent carry a 1/4" T so i had to get the fancy "make your own" with a blank T and some threaded ends. the breather tube has 1/4" ID...the fuel line however does NOT...i either measured or wrote it down wrong, but it looks to be 3/8". i will comfirm this tomorrow.
|03-10-2009 08:25 PM|
i cut a hole on the inside of the tub to line up with the factory filler. i just need to shorten the hoses, looks like it'll line up great. ill post pics later tonight.
i need to pick up some longer lines- i snapped the plastic barb on the breather hose so im just going to get some new hoses while im at lowes.
im also going to replace the snap together fuel to be on the safe side...its stretching to reach. the electrical connections have plenty of slack throughout the body so that dosent need to be messed with.
im going to try a back seat one day, ill try and remember to put something on here if i do.
the body lift is a 1.25" JKS.
|03-10-2009 01:41 PM|
|YjMopower||Nice job man ,keep it up .Did you figure out where your going to put the whole to pump gas in?I plan to do this to my jeep but havent figured out where would i put the hole to pump gas, i was thinking of putting a mini enclousre on top of it, then maybe try adding a back seat.Hopefully its not to high.I Love how jeeps look like without the gas tank in the factory location.But keep it up.btw how much of a body lift you have?|
|03-10-2009 12:11 AM|
i think im done for the night...tomorrow ill be adding atleast one more crossmember, adding tabs to hook ratchet straps to, figuring out the shock situation, and cutting a skid for the bottem(...maybe). Later this week ill be heading over to Nationwide Laser to get a top cut and bent for it. i mean if im losing my back seat it'll atleast look nice.
i plan on it being bolt on/off so i may even get it powdercoated depending on how much they want for it.
|03-09-2009 09:30 PM|
|03-09-2009 08:35 PM|
this way is 40 degrees compared to the origional 60 degrees
Shock Absorber angles
|03-09-2009 08:10 PM|
The write up's im following:
TJ this has alot more pics is you click "this index" at the bottem of his page.
|This thread has more than 30 replies. Click here to review the whole thread.|