Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Tech Forums > Communications and Electronics > CB ground

Join Wrangler Forum Today


Thread: CB ground Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-13-2013 10:14 AM
caprob Just remember on the ground strap that surface area of the wire is EVERYTHING! Braided or flat copper strap (wider the better) is best. Sprap paint or undercoat/Plasticoat over connections when done to prevent corrosion. I did this on my 102" whip to the chassis.
I'm a ex-mega-yacht now ship Captain with lots of experience in the importance of a good ground to plane. Good luck!
02-28-2013 09:07 PM
Magichelmt
Quote:
Originally Posted by aaronarmenta View Post
I think running a ground strap into the tub and attaching it to sanded metal works?
This. I ran a separate ground wire along with the antenna cable. I don't have any inside pics, but I just zip tied them together. I'll get a pic in the daytime. On my JK there is a plastic trim piece on the rear door that snaps out easy. Just run it behind that and find a ground inside. I pulled the trim off the corner and sanded to bare metal at the base of the roll bar. Just make sure you have good bare metal to metal contact for your ground.

02-28-2013 08:25 PM
eton Its because you don't have a ground plane - CB transmits downward reflecting off the ground plane - mount it on the front so that your hood is the ground plane, it'll work better. Off course on the trail just about anywhere will work.... ground to the frame if possible, seal everything up so that it doesn't get wet. Just remember that the ground plane and ground are not the same thing.
02-21-2013 10:37 AM
aaronarmenta I think running a ground strap into the tub and attaching it to sanded metal works?
02-18-2013 08:24 PM
BlueRidgeYJ
Quote:
Originally Posted by BayLLC
Lol thanks and I won't... Just had today to work on it and tried to get as much done as I could in one day
No worries, just messin with ya. I know that situation all too well.
02-18-2013 08:23 PM
BayLLC Lol thanks and I won't... Just had today to work on it and tried to get as much done as I could in one day
02-18-2013 08:13 PM
BlueRidgeYJ Yeah. Get jumper cables, place one lead on the bottom of your antenna mount (the collar that attaches the wire to the stud) and place the corresponding lead onto the frame. If it doesn't get better, youre barking up the wrong tree.

Have you measured your SWR?

I hope you don't bump it every 4 hours, lol.
02-18-2013 06:28 PM
Magichelmt I ran a line from my bracket, through the door with the antenna cable and to the bottom of the roll bar. I sanded down to bare metal on both ends and put a good metal to metal connection. I have no problems.
02-18-2013 05:27 PM
BayLLC Bump
02-18-2013 01:23 PM
BayLLC
CB ground

I have my CB antenna mounted behind my spare tire and have it grounded to the bolt of the mount... Pics below... This is not giving me a strong signal so I'm thinking I need to get the ground down to the frame but I'm having trouble finding a clean way to do this with ought obstruction the opening of my tailgate

Any ideas?

Attachment 211386



Attachment 211387

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:00 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC