Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > alarm blinkers tap in

Join Wrangler Forum Today


Thread: alarm blinkers tap in Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-01-2006 12:30 PM
Tiburon No prob, I've been installing alarms for about 3 years now so if you have any more questions just hit me up. I installed door locks in my doors and just need an alarm to hook em up. I'm waiting to get a cheap Viper 2 way and microwave sensor before I install any more.
12-01-2006 12:05 PM
Triple88a Thanks Tiburon ill see what i can do... For now i think ill install the alarm just so it screams when sensing shocks and later on i will go behind the dash.. It just started snowing here and its less than 30 F at this very moment i'm not planing to open everything up and have to do it again later for a better job...
12-01-2006 11:14 AM
Tiburon the alarm brain has a wire dedicated to run the flashers, it is pulsed to turn on and off automaticly, you can sometimes set it to stay on steady. the wire you need is Black with a yellow stripe, its located at the switch so you'll need to get behind the dash to get it. You can sometimes find the wire in the bundle that runs to the back on the drivers side kick panel. Make sure you use a test light or a mulit meter to test the wire before you tap it in. good luck
11-30-2006 02:02 PM
hardy1531 If I read the diagram right I believe you are gona look for a pink wire that comes out of the steering coloum. You would need to test to make sure though
11-30-2006 12:25 AM
Triple88a Thanks Hardy quite a lot of stuff there.. all i found was the switch though which i'm not planing on breaking into I gues i gotta follow the wires.. any other feedback is welcome as well

I'm a bit confused whats happening inside the switch is self.. all i want to do is use a relay to make it seem like i turned on the hazard flashers
11-29-2006 10:08 PM
hardy1531 hey found this on another thread hope it helps....
http://www.vintagemusicprojects.com/...emanuals/TJ98/
11-29-2006 09:42 PM
Triple88a
alarm blinkers tap in

Hey all i just received my 2way alarm. I'm wondering where should i connect the wires for the blinkers? For those who arent familiar.. its a 12V output from the alarm.. where and which wire should i tap into so i can make the blinkers work when 12V is applied to it?

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:53 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC