|09-14-2013 11:12 PM|
Nice clean solution but maybe a few bucks overpriced for what it is.
|09-10-2013 08:43 AM|
|09-07-2013 05:13 PM|
|09-07-2013 08:15 AM|
And if you have an auto then you remove the block off plate for the clutch master cyl (that your auto would not have) and you have a 1" hole for running a lot of wires.
|09-06-2013 12:30 AM|
|Jerry Bransford||If you have a manual transmission, there is a rubber grommet plugging a hole in the firewall available just above & to the right of the accelerator pedal. Drill a small hole through the center of the rubber grommet and it's perfect for passing wiring through. That grommet isn't there when you have an automatic as that is where the auto transmission's shifter cable passes through.|
|09-05-2013 10:43 PM|
|09-05-2013 09:05 PM|
|Jerry Bransford||He must have forgotten to post the photos, they aren't there for me either.|
|09-03-2013 03:42 PM|
Hey, message #3 above says "in my pic you can see..."
I'm logged in, but there are no pictures in this thread. What's up?
|02-26-2013 11:13 AM|
Thanks Jerry, that is my plan. Where have you come through the firewall? Did you pick up a ground to the tub, or run to the battery negative terminal?
Looks like I have the antenna routing sorted out.
|02-25-2013 06:57 PM|
For the best and quietest/noise-free CB radio installation, always power a 2-way directly to the battery. Other sources like cigarette lighter receptacles, random fuse connections, etc. are likely to introduce electrical noise into the CB... like alternator whine, ignition noise, fuel pump noise, etc.
And there is really no need to worry about the power source being switched so it shuts off when the ignition is turned off. It would take weeks for a CB being on and in Standby mode for it to drain the battery, they just don't draw that much power unless they are transmitting. Not to mention it's handy to be able to use the CB without having to turn the ignition switch on.
|02-25-2013 07:45 AM|
I have searched previous threads and not found specific antenna routing methods for getting the antenna cable into the jeep.
I have an 05 LJ and will be using a SS driver side tail light mount. What is the best routing from the tail light area? I have seen folks just run it up through a gap in the soft top, but don't care for that approach.
|04-10-2012 11:57 AM|
|corey2491||I bought the bundle from Quadratec, with the antenna, mount and coax. Then a small Cobra 19 and a Rugged Ridge dash mount so that I didn't have to drill. It took us about 40 minutes from start to finish and we wired it to the fuse panel under the glove box.|
|03-25-2012 09:51 AM|
I would go direct to the battery or at least the main battery terminal feeding the fuse/breaker panel under the hood. The pic above showing access through the firewall is right next to the battery and that terminal. The suggestion for using the lighter is good, but I would go direct to the battery and put some type of disconnect in your wiring. There are several varieties of connectors you can crimp or solder on your wire so you can disco the radio. You may have a radio with a removable power harness, which solves the issue.
Antenna wiring. The basics: the coax has a center conductor and a shield around that conductor. The shield and center conductor can never touch. The shield needs to be connected to a good vehicle ground (frame or negative battery or both). The center conductor has to connect to the antenna itself and CANNOT be grounded.
|03-25-2012 09:36 AM|
Connect the Positive, Connect the Negitive then the antenna wire! Hardest part is routing antenna wire from interior to exterior.
Also consider a remote speaker depending on where your going to mount CB...Mounted mine below my dash radio, but I have an a ELCHEAPO CB ($30 MIDLAND) and the internal speaker is crappy..bought a small remote speaker aimed right at me.
|03-25-2012 09:06 AM|
clean power is best, from the battery. its easy to get it into the cab.
in my pic you can see the red wire going into the cab...and a screwdriver showing how you can get through that foam. any ground from inside the cab will work. only two wires needed to power the cb. then other than running the coax and a good antenna mount and you are golden
|03-25-2012 08:10 AM|
|AV8R||If you go topless a lot or have a soft top, consider an installation that will allow you to easily remove the CB from its bracket. I wired mine to a cigarette lighter plug for even quicker removal/install that doesn't leave power wires visible and hanging.|
|03-24-2012 10:11 PM|
I've seen alot of threads in here about CB radios and such and I have a question I've had a question about. Before I jump into buying my whole set up I want to know how to wire it, like the whole thing from the battery to the cab to the antenna wiring. I'm sure it'll be simple once I get into it but I hate jumping into things not knowing for sure. So does anyone want to post pics or like a step by step for a safe, clean installation? On a side note I plan on getting a behind the tail light mount on the drivers side. Thanks in advance.