|09-29-2013 09:59 AM|
|lee indy||I've had to pound the bottom lip of Mine back straight a few times. And a solid over travel stop would be nice too|
|09-29-2013 09:36 AM|
|Riccochet||Robocop has the same setup I do. Bought mine from JeepAddons. No issues with my bumpers.|
|09-28-2013 05:34 PM|
I have had mine for about 6 months and had no issues at all. I rarely get off road and honestly bought mine for looks. No rust issues as of yet however I could just as easy remove and bedline them myself if any rust shows up.
|09-28-2013 05:23 PM|
|donmeca2020||If this is an ebay product BEWARE..... im not saying everything on ebay is made cheap and poorly but quite abit of things on ebay are.|
|09-28-2013 04:52 PM|
I got my paramount restyling rear bumper with tire carrier last year and have had
no problems I grease my tire hinge about every 4 or 5 months but I am in nor cal
|09-28-2013 03:35 PM|
|09-28-2013 10:37 AM|
|09-28-2013 09:38 AM|
|09-28-2013 07:01 AM|
|09-28-2013 04:06 AM|
|nodak2222||Glad I found this thread! I was going to do the smittybilt xrc front and rear bumpers but will now be ordering paramount from jeepaddons.com!|
|06-07-2013 03:45 PM|
|troy b||Yes I will indeed say that Chris is a great guy to work with, just ordered the rear bumper with tire carrier, painless transaction and he hooked me up too! Now, just to wait until I get home and can install it lol|
|05-29-2013 08:54 PM|
|sjbohman||Thanks for the info! Bought the winch today!|
|05-28-2013 10:23 PM|
|ToplessTN||I took the grille off today to install the Rugged Ridge grille kit and TruckLites. Taking the grille off was not a problem at all with the new bumper.|
|05-27-2013 11:23 PM|
Washing and waxing the grille isn't a problem. I washed it yesterday after the install. There's a 1.25" gap.
The winch holes are 10" x 4.5". The width of the flat area where the winch would go is 25" x 7.875".
|05-27-2013 11:04 PM|
|sjbohman||I have this bumper at home in Texas.... bought from Jeep Add On's also...good people... question...I'm on the road and my wife doesn't want to measure the winch plate...I stop for tampax but she can't help me....Thinking about a warn zeon 10 but I hear fit problems on some bumpers...its 24.25 inches wide and 7.2 inches deep...any chance one of you guys with one can measure for me?|
|05-27-2013 09:33 PM|
How hard will it be to wash and wax the lower corners of the grill? I'm on the fence on bumper this bumper.
|05-27-2013 05:32 PM|
I got the Paramount front with LEDs and ear with tire carrier from JeepAddOns on Friday. Scott gave me great service and an excellent price. Less than $900 shipped for all.
There isn't a lot of firsthand info that I could find about these bumpers, so I'll add some of my experiences/thoughts.
Both bumpers came with D-Rings. 4 in total.
There were no blemishes on either bumper and no missing bolts. No instructions though. The bumpers were packed incredibly well. Inner layer of foam wrap, then a layer of cardboard, then a layer of plastic wrap and shipping tape, all enclosed in boxes.
The hardest part of the install for me was getting the stock front bumper off. The air damn and cover plate screws were a bitch. Ended up ripping the air dam off and dremeling the screws and nuts.
I installed both bumpers by myself in the garage with hand tools in about 4 hours.
After the first try the rear tire was tilting out and I didn't like the look. I pulled the spare tire off, loosened all the bolts, then inserted my receiver hitch into the receiver and used my floor jack to lever it up. I used a level to get it leaning a little inboard then tightened the bolts back up. Looks much better now.
I have a 2012 JKU and I didn't have to relocate the vacuum canister.
As others have said, the instructions for wiring the LEDs on the front bumper suck. They included a box that's supposed to make the outboard LEDs works as DRLs but I haven't tried wiring them up yet. The round LEDs are 4 LEDs each and the straight center ones are 5 LEDs each.
I'm running 35s and I set the piece that holds the tire to the tire carrier at it's lowest setting. I still have an inch or two of clearance between the tire and bumper. I left the stock tire bumpers on for now. I'll either take them off completely or change them to Daystars. They're a bit squished with the way I have the bumper set now.
I drove it for 300 miles yesterday with the top off and there was a little rattling when I hit potholes and such, but not enough to notice if you aren't looking for it.
If you're concerned about cops, you'll want to get a license plate relo kit. The tire mechanism locking handle blocks the rightmost letter of my plate. Also, you'll need a new 3rd brake light.
The rock crawler bumper with LEDs is a mid-width bumper.
I highly recommend this combo to anyone interested and I recommend contacting Scott at JeepAddOns as well.
The front bumper:
The rear bumper with tire carrier:
|05-14-2013 11:21 AM|
|05-07-2013 06:00 AM|
|05-07-2013 05:45 AM|
|05-06-2013 08:35 PM|
|05-06-2013 08:17 PM|
|05-06-2013 08:03 PM|
|05-06-2013 08:00 PM|
|Riccochet||Just ordered my set from JeepAddons. Awesome people over there.|
|05-04-2013 07:31 PM|
|Currey||Think the rear tire needs to come down a little bullit?|
|05-04-2013 06:54 PM|
|05-04-2013 06:40 PM|
|05-04-2013 06:30 PM|
|05-04-2013 12:29 AM|
|Currey||Spent the evening installing the xrc style bumpers (front, rear, and tire carrier) and xrc8 comp series winch. Pics coming tomorrow.|
|04-30-2013 03:23 PM|
|This thread has more than 30 replies. Click here to review the whole thread.|