Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Ball Joints and tie rods

Join Wrangler Forum Today


Thread: Ball Joints and tie rods Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-07-2013 11:40 AM
rubiconvict05 So I have decided to do the ZJ up grade. Now that part will be sufficient enough for what I do. I have decided that I do need to upgrade the other area that is doesn't cover. Has anyone found a sutiable replacement?

Also what are thoughs on Crown Ball joints opposed to Moog?
Ball Joint Kit Includes Hardware 83500202
03-06-2013 12:48 PM
rubiconvict05 I actually have some aftermarket draglink tube and I am going to see later today if it will fit the ZJ tie rod ends. I know it fits the threads for the gm 1 ton Tie rods but maybe I will luck out and not have to drill my knuckles out. All in all I do have to take the knuckles off to replace the ball joints and I have access to a drill press.

No I am not using an adjustable track bar. The Fab tec kit had a template on where to drill the new location hole in the stock bracket.
thank you for your input.
03-06-2013 12:06 PM
Cons_Table
Quote:
Originally Posted by rubiconvict05 View Post
These are the components I plan to use.

Rugged Ridge Heavy Duty Tie Rod Kit (this is also a cross over steering set up
part number 18050.82 from Morris 4x4

Energy Suspension Control Arm Bushing Kit Front
Part number 29024-03150822 from Parts Geek

Moog Ball Joints Full set left and right upper and lower
-these allow some camber and caster adjustment. Havent found where to get these yet at the cheapest price. Most likely Rock auto

Already have the Moog front track bar, plan to bring that in for the warrenty as it is lifetime.

What do you guys think Is this a smart set up? I want to remove all play in my steering and get it ready for an alignment prior to getting new tires.
I would probably avoid that steering setup. I have heard people say that that particular setup on a jeep has dead spots in the steering. I also believe the joints arent too good on it. If you've got the money, definitely go with the Currie setup. It is stout, and a great upgrade over stock. If you can't swing that much on steering right now. The ZJ upgrade is good too. It uses the same drag link as stock, but the tie rod is stronger and has bigger ends.

Also with 4.5" of lift, you arent using an adjustable track bar? Are you using a bracket instead?
03-06-2013 11:59 AM
rubiconvict05 These are the components I plan to use.

Rugged Ridge Heavy Duty Tie Rod Kit (this is also a cross over steering set up
part number 18050.82 from Morris 4x4

Energy Suspension Control Arm Bushing Kit Front
Part number 29024-03150822 from Parts Geek

Moog Ball Joints Full set left and right upper and lower
-these allow some camber and caster adjustment. Havent found where to get these yet at the cheapest price. Most likely Rock auto

Already have the Moog front track bar, plan to bring that in for the warrenty as it is lifetime.

What do you guys think Is this a smart set up? I want to remove all play in my steering and get it ready for an alignment prior to getting new tires.
03-05-2013 02:07 PM
UFOtestpilot If you want to gain caster you would want offset ball joints, if you don't need the caster adjustment, or don't want to use offset ball joints to get it, then don't use them. I went with the Dana/spicer ball joints and I am perfectly happy with their construction and fitment.
03-05-2013 01:08 PM
EMTJEEP I don't know how to tell about the offset balljoints but I'm sure you only need the regular ball joints. Here's a helpful link I used when I did my ball joints. D30 Ball Joint Replacement - 1

I would go for the Currie CurrectLync system. CURRIE CE-9701 CURRECTLYNC® - HD TIE ROD SYSTEM - Savvy Off Road Aluminum It's a better choice over the Rugged Ridge and ZJ upgrade. I installed it when I did my hubs and ball joints. And I'm sure most of the people on this forum would agree with the Currie system being better.

Also check all your important components when you put your jeep back together.

03-05-2013 12:02 PM
rubiconvict05
Ball Joints and tie rods

I will be replacing my ball joints, There is play in all 4 of them and I finially have money to rebuild my front end.

What i am wondering is how can I tell If I need off set ball joints? I have seen these as a option and I want to be sure I don't Put new ones in and then get it up on the rack and need to change them to get my steering correct.

Later today I will list the parts i plan to use for the complete rebuild, I searched and couldn't come up with an easy answer for what to do.

I am also looking into the Rugged Ridge heavy duty steering kit. Should I do this or just do the ZJ? up grade on the linkage. I have also seen some other nice bolt in kits.

Any help would be much appreciated. Thank you guys.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:53 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC