|03-28-2013 05:22 PM|
Sounds like the tires have balancing beads in them. 35" tires should balance with regular wheel weights. Will probably want to get them rebalanced and do the chalk test to find the right psi for your Jeep.
Can you post pictures of your suspension? That would give us a better idea of what you have and don't have.
But from just reading your descriptions, it sounds like you will want to invest in front lower control arms, rear upper control arms and front and rear adjustable track bars to get your suspension back in line. These parts will make a night and day difference in the drivability.
|03-27-2013 06:41 PM|
|Duma||Nice work tracking down possible causes and finding the worn inner tie rod. I just recently learned about the BB's in the tires trick to balance them. Pirate 4x4 has some threads detailing how many ounces to use in each tire, regular BB's vs ceramic. I just have regular wheel weights. But to answer your question, yes- out of balance wheels can contribute to DW.|
|03-27-2013 03:46 PM|
|ty04orange||I forgot to mention that while I had the Jeep wheels and tires off (also checked the brakes, lines, rotors, etc) that I noticed the tires sounded like they were full of beads or sand. I did some research because I have never heard of that. My F150 also has 35s on it, although not as aggressive, and they did not require filler to balance. My Jeep wheels have no weight on the outside. I am not a fan of this method of balancing. What are your thoughts? Could I have a tire that is so badly out of balance (due to bad balancing, rotation of tires, etc) that is causing the resonance and DW? That is the last thing I can think of. I am going to replace the shocks, plan on ordering some in the next day or so and see if that helps at all.|
|03-26-2013 07:42 PM|
|jp2611||I am glad you are making progress and actually understand that while what is said on here may not be what you want to hear, it is said in the interest of trying to make you and your Jeep safe and more enjoyable to drive.. GL figuring out where the rest of any issues are....|
|03-26-2013 07:38 PM|
It still has the factory track bar, with a drop down bracket. I went through the Death Wobble checklist today, and basically took every component off, one at a time, looking for loose or broken parts. The inner tie rod end (that connects to the pitman arm) was trash. Everything else was nice and tight, no wobble or play in any components, no broken welds, no ovaled mount holes, no bound up bushings, etc. I put 9/16 bolts back in the track bar, like the checklist recommends. I havent driven it since I did all of this because I know it needs an alignment and I cannot get one until next friday. Also, there was no play in the ball joints or anything. There is some slop in the steering still, but I am not about to take the steering box off or fool with it, as the play in the steering wheel isnt that bad.
You didnt rain on my parade, man. Rough Country being a cheap lift does not bother me. It is not a rock crawling suspension, it is a mall crawling suspension, and that is fine with me at this point. I do not plan on doing any hardcore wheeling in it. It has new(ish) shocks all around though, and does not ride too incredibly rough. I will let you all know when I get it back out this weekend and take it for a test drive and let you know if any of this made a difference.
|03-26-2013 12:47 PM|
Aside from taking it into to have the suspension/steering professionally gone through, you could download the install instructions and make sure it was installed correctly. Then take it in for a proper alignment. But even then you will likely continue to fuss with the lift (replacing bushings occasionally and stiff stocks) in a matter of time.
|03-26-2013 11:57 AM|
|bcasey||Does it still have the original front trackbar? If the trackbar is loose at all it will feel like the steering is not responsive and you need to have one steering stabaliser on. If you have the stock trackbar on you may wanna upgrade to a adjustable trackbar such as JKS or Currie.|
|03-26-2013 07:54 AM|
|Ltblue||Ty.. looks like the previous owner never really did his homework when modding the jeep. Probably wanted it more for looks then functionality, definitely read through the Death Wobble sticky thread to find your problem.|
|03-25-2013 09:06 PM|
Well, you found out why the previous owner had 2 stabilizers installed.
Read the death wobble stickies and go through the list, you'll find the issue.
If the Pitman arm nut was loose, i bet you may find other stuff not torqued correctly.
|03-25-2013 08:57 PM|
|ty04orange||Just watched the death wobble videos on here, and that is definitely what happened... Jeez!|
|03-25-2013 08:55 PM|
|ty04orange||Well, some bad news from the home front. I have never been so scared in my life as I just was. I took both stabilizers off and tightened the pitman arm nut and took it for a spin. I was going about 30 miles an hour and noticed that it turned a lot quicker than it did with them installed. I swerved once left, once right and once left and got what I imagine is the death wobble (felt like it was bouncing from one tire to another to another to another) and it terrified me. I just knew I was gonna lose control. If that had been a crowded road, there would have been an accident. I guess the stabilizers were added to hide the wobble, which means I have bigger problems and probably worn out or broken parts that I havent even found yet....|
|03-25-2013 08:50 PM|
Mine was wandering all over when I bought it, so I've been through allot of this troubleshooting.
But Yah, lower the air pressure and be sure to check toe in, should be 1/8" to 1/16" closer in front.
There are good sticky posts describing how to check it and adjust as needed.
|03-25-2013 08:40 PM|
|ty04orange||I got the torque on the pitman arm bolt to the correct setting. It was at roughly 135lbs and I took one stabilizer off. It made night and day difference. It got rid of most of the "floaty" feeling that it had before. I am about to go take the other off and try it then. I can put one back on or whatever, depending on how it drives. Thank you all very much for the input so far!|
|03-25-2013 08:33 PM|
Do not drive it.
The nut on the Pitman arm should be 185 foot-pounds of torque or around there. There are splines on it as well so if there is slop or play there is an issue.
|03-25-2013 08:16 PM|
|ty04orange||Ok, I will let some pressure out of the tires, and that might help. I just took one stabilizer off and am about to go drive it a little. After closer inspection, I dont believe there is a lift on it at all... I didnt think 35s would clear so easily without a lift, but I cannot see any added brackets or anything that would have lifted it at all. I dont even see any coil spring spacers or anything, but I will take some pics when I get back and post them up on here. This is baffling me to be honest. There appears to be a little play in the pitman arm, as I had my wife sit in the drivers seat, center the wheel and move it back and forth so I could see the play. The play appears to be the shaft into the top of the pitman arm because I can see the shaft moving around inside the pitman arm before the pitman arm engages and starts to move the wheels.|
|03-25-2013 08:01 PM|
|03-25-2013 07:47 PM|
|03-25-2013 07:38 PM|
|ty04orange||I have 32# in each, which is what the tire says to run|
|03-25-2013 07:32 PM|
And if the steering wheel is off center one side then the other, you probably should stop driving it until you fix it. Unsafe!
Check connections from shaft into power steering box, and check connections from Pitman arm to tie rod (drag link).
Also what are you running for tire pressure?
|03-25-2013 06:47 PM|
Well, you need to get rid of one stabilizer, check all torque on steering components, check for worn or play in joints and bushings, then check toe in and caster.
Take a few pics and post them, guys here will spot any issues.
|03-25-2013 06:46 PM|
|ty04orange||Does not seem to have adjustable control arms.. And we just drove to get dinner. When we backed out of the garage, the steering wheel was off center, to the right. Then on the way back I noticed the steering wheel was off center to the left. It almost feels like something is broken or worn out, like I said earlier. The steering doesnt feel proportional to the amount the wheel actually turn. It is hard to describe|
|03-25-2013 05:38 PM|
|03-25-2013 05:37 PM|
Well, I drove it to the store a little while ago, and I think I discovered how to describe it. My wife has a Nissan Juke and it has electronic steering. Turning the steering wheel sends a signal to a motor that turns the wheels. No direct connection. That is kind of the way the Jeep feels. It is almost like what I put in with the steering wheel is not directly linked to what the wheels are doing. Severe understeer. I see a "high steer kit" on quadratec but am not sure if I have that or not.
I believe the dual stabilizers were part of the lift kit, because it is a nice kit, with a skid plate on the axel where it connects, and has 2.2 cut out of it, and it has 2.2 shocks on it. I am not against taking it off and driving it to see if that helps, and can always put it back on if it doesnt help. If I cant figure it out soon, that is exactly what I will do.
|03-25-2013 05:36 PM|
|Duma||Does the lift have adjustable control arms? If steering is sketchy at speed, incorrect caster angle and/or toe-in may be the culprit. Sounds like the seller slapped on a 4" lift on the cheap and didn't do it right. (just check how many posts on this forum are asking how to lift as cheaply as possible). I'd recommend taking it in to a 4x4 shop for a full alignment. They'll be able to pinpoint the issue. Also, if your steering wheel wasn't recentered after the lift, that can cause abs and other problems (the computer thinks you're in a slide).|
|03-25-2013 05:15 PM|
Have heard it said that if everything is "right" you shouldn't need any stabilizer....think they are mostly for on road use....
|03-25-2013 05:12 PM|
|ty04orange||I thought stabilizers were on there to make it steer better? What is their function and how is taking them off supposed to help? I am not being a jerk, just want to learn as much as I can.|
|03-25-2013 10:43 AM|
|03-25-2013 10:33 AM|
|ty04orange||So you think I should take the stabilizers off all together? No stabilizer then? I do turn the trac control off, but the ESP light still comes on from time to time|
|03-25-2013 10:12 AM|
|Ltblue||I'm no expert, It could be a lot of things.. From what you have mentioned, it could be steering stabilizer, wheel alignment, tire pressure, etc. most likely it sounds like your problem is with the dual steering stabilizer. ESP should be turned off if you have a lift.|
|03-25-2013 10:03 AM|
Did it drive like this when you test drove it before you bought it??
Either way, first thing I would do is ditch that dual SS setup you've got going on.
From my experience, when something like an ABS sensor goes out, you will experience symptoms like you noted with the brakes feeling like they are grinding. Goes away once the sensor is replaced. Not sure if this goes hand in hand with that ESP light though.
|This thread has more than 30 replies. Click here to review the whole thread.|